Zum Hauptinhalt wechseln

Brightsign 4k Battery Replacement

Was du brauchst

  1. Brightsign 4k Battery Replacement, Outer Shell: Schritt 1, Bild 1 von 3 Brightsign 4k Battery Replacement, Outer Shell: Schritt 1, Bild 2 von 3 Brightsign 4k Battery Replacement, Outer Shell: Schritt 1, Bild 3 von 3
    • Remove three 8mm screws from the left side of the device.

    • Remove four 8mm screws from the right side of the device.

  2. Brightsign 4k Battery Replacement: Schritt 2, Bild 1 von 3 Brightsign 4k Battery Replacement: Schritt 2, Bild 2 von 3 Brightsign 4k Battery Replacement: Schritt 2, Bild 3 von 3
    • Apply pressure on the SD card to pop it out of the port.

    • Remove the card by pulling it out.

  3. Brightsign 4k Battery Replacement: Schritt 3, Bild 1 von 3 Brightsign 4k Battery Replacement: Schritt 3, Bild 2 von 3 Brightsign 4k Battery Replacement: Schritt 3, Bild 3 von 3
    • Press down on the top cover of the device and slid it towards you until you see a slight gap created.

    • Lift the top cover off.

  4. Brightsign 4k Battery Replacement: Schritt 4, Bild 1 von 3 Brightsign 4k Battery Replacement: Schritt 4, Bild 2 von 3 Brightsign 4k Battery Replacement: Schritt 4, Bild 3 von 3
    • Slide the body case back away from the bottom.

    • Pull up the body case to remove it from the bottom.

  5. Brightsign 4k Battery Replacement, Motherboard Removal: Schritt 5, Bild 1 von 2 Brightsign 4k Battery Replacement, Motherboard Removal: Schritt 5, Bild 2 von 2
    • Remove the four 8mm screws at each corner of the motherboard with a JIS #0 screwdriver.

  6. Brightsign 4k Battery Replacement: Schritt 6, Bild 1 von 2 Brightsign 4k Battery Replacement: Schritt 6, Bild 2 von 2
    • Lift the motherboard out of the casing.

  7. Brightsign 4k Battery Replacement, Battery: Schritt 7, Bild 1 von 2 Brightsign 4k Battery Replacement, Battery: Schritt 7, Bild 2 von 2
    • Flip the motherboard over.

    • Desolder the two solder joints and remove the melted solder.

    • Beware of over heating the soldering kit will damage the logic board.

  8. Brightsign 4k Battery Replacement: Schritt 8, Bild 1 von 3 Brightsign 4k Battery Replacement: Schritt 8, Bild 2 von 3 Brightsign 4k Battery Replacement: Schritt 8, Bild 3 von 3
    In diesem Schritt verwendetes Werkzeug:
    Desoldering Pump
    $3.99
    Kaufen
    • Apply the desoldering pump to remove the melted part from the motherboard (press the button to release it).

    • Pull the battery from the motherboard.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tuong Ngo

Mitglied seit: 02/15/18

85 Reputation

1 Anleitung geschrieben

Team

USF Tampa, Team S17-G6, Boczar Spring 2018 Mitglied von USF Tampa, Team S17-G6, Boczar Spring 2018

USFT-BOCZAR-S18S17G6

4 Mitglieder

6 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 1

Letzte 30 Tage: 4

Insgesamt: 402