Zum Hauptinhalt wechseln

RedOctane X-Plorer Whammy Bar Replacement

Was du brauchst

  1. RedOctane X-Plorer Whammy Bar Replacement, Rear Case: Schritt 1, Bild 1 von 2 RedOctane X-Plorer Whammy Bar Replacement, Rear Case: Schritt 1, Bild 2 von 2
    • Remove the strap by pulling it off of the mounts located on the body and neck.

  2. RedOctane X-Plorer Whammy Bar Replacement: Schritt 2, Bild 1 von 3 RedOctane X-Plorer Whammy Bar Replacement: Schritt 2, Bild 2 von 3 RedOctane X-Plorer Whammy Bar Replacement: Schritt 2, Bild 3 von 3
    • Remove the nine 12mm Phillips #1 screws around the perimeter of the case with a screwdriver.

    • Remove the two 15mm Phillips #1 screws connecting the body panel to the neck panel with a screwdriver.

    • These screws can also be Torx on some models.

    • Pull off the rear case.

  3. RedOctane X-Plorer Whammy Bar Replacement: Schritt 3, Bild 1 von 3 RedOctane X-Plorer Whammy Bar Replacement: Schritt 3, Bild 2 von 3 RedOctane X-Plorer Whammy Bar Replacement: Schritt 3, Bild 3 von 3
    • Remove the five 12mm Phillips #1 screws along the neck with a screwdriver.

    • Pull off the top shell of the neck to expose the internal features.

  4. RedOctane X-Plorer Whammy Bar Replacement, Whammy Bar: Schritt 4, Bild 1 von 3 RedOctane X-Plorer Whammy Bar Replacement, Whammy Bar: Schritt 4, Bild 2 von 3 RedOctane X-Plorer Whammy Bar Replacement, Whammy Bar: Schritt 4, Bild 3 von 3
    • Remove the two 7mm Phillips #2 screws from the black wire retainer.

    • Pull off the black wire retainer.

  5. RedOctane X-Plorer Whammy Bar Replacement: Schritt 5, Bild 1 von 1
    • Reach one finger under the guitar to push the whammy bar and its attached components from the case.

  6. RedOctane X-Plorer Whammy Bar Replacement: Schritt 6, Bild 1 von 2 RedOctane X-Plorer Whammy Bar Replacement: Schritt 6, Bild 2 von 2
    • Remove both of the plastic side tabs by gently pulling them off.

  7. RedOctane X-Plorer Whammy Bar Replacement: Schritt 7, Bild 1 von 1
    • Remove the two plastic tabs from the whammy bar casing.

    • Keep the spring connected to the plastic tabs throughout this step.

  8. RedOctane X-Plorer Whammy Bar Replacement: Schritt 8, Bild 1 von 1
    • Using two hands, remove the spring from the plastic tabs.

Abschluss

To reassemble your device, follow these instructions in reverse order.

3 weitere Nutzer:innen haben diese Anleitung absolviert.

[deleted]

Mitglied seit: 04/18/18

175 Reputation

1 Anleitung geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 4

Letzte 7 Tage: 13

Letzte 30 Tage: 82

Insgesamt: 3,462