Zum Hauptinhalt wechseln

Solio CLASSIC2 Electric Wire Replacement

Was du brauchst

  1. Solio CLASSIC2 Electric Wire Replacement, Disconnecting the Battery: Schritt 1, Bild 1 von 1
    • Turn off the device by pressing on the clear power button behind the device.

    • To make sure that it is off, make sure the button is not flashing green.

  2. Solio CLASSIC2 Electric Wire Replacement: Schritt 2, Bild 1 von 1
    • Using the Phillips #1 screwdriver, remove the 2mm screw located on the bottom of the device, near the hinge.

  3. Solio CLASSIC2 Electric Wire Replacement: Schritt 3, Bild 1 von 3 Solio CLASSIC2 Electric Wire Replacement: Schritt 3, Bild 2 von 3 Solio CLASSIC2 Electric Wire Replacement: Schritt 3, Bild 3 von 3
    • Using the plastic opening tools, gently pry open the side of the large panel.

    • Keeping the tool in, slowly slide the tool along the side of the panel.

  4. Solio CLASSIC2 Electric Wire Replacement: Schritt 4, Bild 1 von 2 Solio CLASSIC2 Electric Wire Replacement: Schritt 4, Bild 2 von 2
    • Rotate the device 180 degrees.

    • Make sure the opening on other side of the device does not snap closed.

    • Gently slide the plastic opening tool along the side of the panel.

  5. Solio CLASSIC2 Electric Wire Replacement: Schritt 5, Bild 1 von 2 Solio CLASSIC2 Electric Wire Replacement: Schritt 5, Bild 2 von 2
    • Do not fully pull apart the back panel from the device. Doing so can rip the two red and blue wires attached to the panel.

    • Using both hands, slowly pull apart the back panel from the rest of the device.

    • Gently flip the back panel open so the circuit board faces up and the two panels are side by side.

  6. Solio CLASSIC2 Electric Wire Replacement: Schritt 6, Bild 1 von 2 Solio CLASSIC2 Electric Wire Replacement: Schritt 6, Bild 2 von 2
    • Softly pinch the red and blue wires close to the white connector.

    • To pull the wires out, wiggle them back and forth until the connector is fully out.

  7. Solio CLASSIC2 Electric Wire Replacement, Circuit Board: Schritt 7, Bild 1 von 1
    • Unscrew the three 2mm screws holding the circuit board down using a Phillips #1 screwdriver.

  8. Solio CLASSIC2 Electric Wire Replacement: Schritt 8, Bild 1 von 1
    • Make sure the white USB port cover on the side of the device is pulled out or you won't be able to lift the circuit board.

    • Gently lift the circuit board out of the device using tweezers.

  9. Solio CLASSIC2 Electric Wire Replacement, Electric Wire: Schritt 9, Bild 1 von 2 Solio CLASSIC2 Electric Wire Replacement, Electric Wire: Schritt 9, Bild 2 von 2
    • Soldering can melt key components and cause harm to both the user and the device. Read soldering guide before attempting.

    • Using a solder iron with a fine tip, slowly solder off the broken wire from the first connection point.

    • Repeat for other connection point of wire.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Kelly Perkins

Mitglied seit: 10/20/13

110 Reputation

1 Anleitung geschrieben

Team

Cal Poly, Team 4-28, Amido Fall 2013 Mitglied von Cal Poly, Team 4-28, Amido Fall 2013

CPSU-AMIDO-F13S4G28

4 Mitglieder

7 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 2

Insgesamt: 283