Zum Hauptinhalt wechseln

HTC Desire 700 Dual Sim Rear Facing Camera Replacement

Was du brauchst

  1. HTC Desire 700 Dual Sim Rear Facing Camera Replacement, Back Cover: Schritt 1, Bild 1 von 1
    • Use the spudger to pry the back cover off.

  2. HTC Desire 700 Dual Sim Rear Facing Camera Replacement, Removing Battery: Schritt 2, Bild 1 von 1
    • Use spudger tool to pry under the battery to lift it up and out.

  3. HTC Desire 700 Dual Sim Rear Facing Camera Replacement, Remove 8 Torx Screws: Schritt 3, Bild 1 von 1
    • Remove eight 8.3mm T4 screws with the Torx screwdriver.

  4. HTC Desire 700 Dual Sim Rear Facing Camera Replacement, Prying Off Rear Panel: Schritt 4, Bild 1 von 1
    • Pry the back panel of the screen using the plastic opener.

    • Work your way gently around the device, using picks as necessary to keep the back panel separated.

    • Use caution not to damage the device, as it takes force to remove the rear panel.

  5. HTC Desire 700 Dual Sim Rear Facing Camera Replacement, Motherboard: Schritt 5, Bild 1 von 1
    • Remove the 3mm PH00 screw located at the bottom center of the motherboard using a P#00 Phillip's head screwdriver.

  6. HTC Desire 700 Dual Sim Rear Facing Camera Replacement, Disconnect Vibrator Wire: Schritt 6, Bild 1 von 1
    • Using the tweezers gently disconnect the wire from the vibrator located on the motherboard.

  7. HTC Desire 700 Dual Sim Rear Facing Camera Replacement: Schritt 7, Bild 1 von 1
    • Remove volume control button ribbon with tweezers.

  8. HTC Desire 700 Dual Sim Rear Facing Camera Replacement: Schritt 8, Bild 1 von 1
    • Carefully remove the ribbon attached to the top of the motherboard.

  9. HTC Desire 700 Dual Sim Rear Facing Camera Replacement: Schritt 9, Bild 1 von 1
    • Unsnap the wire from the printed circuit board (PCB) using the tweezers.

  10. HTC Desire 700 Dual Sim Rear Facing Camera Replacement, Remove Rear Facing Camera: Schritt 10, Bild 1 von 1
    • Carefully remove the ribbon that attaches the camera to the front screen using the tweezers and the plastic opening tool.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

Steven Pate

Mitglied seit: 09/23/14

191 Reputation

7 Anleitungen geschrieben

Team

USF Tampa, Team 9-3, Blackwell Fall 2014 Mitglied von USF Tampa, Team 9-3, Blackwell Fall 2014

USFT-BLACKWELL-F14S9G3

4 Mitglieder

14 Anleitungen geschrieben

2 Kommentare

my screen conector on the motherbord got damaged what can i do about it?

stboscoojo - Antwort

On step 10, what is that big copper cover? Is it an LNA shield? What is the right tool to remove it?

Thank for this tutorial

Aissa Brahimi - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 0

Insgesamt: 1,359