Zum Hauptinhalt wechseln

Nerf Recon CS-6 O-Ring Replacement

Was du brauchst

  1. Nerf Recon CS-6 O-Ring Replacement, Remove Magazine: Schritt 1, Bild 1 von 1
    • Skip this step if magazine is already removed.

    • Pull slide back.

    • Pull backwards on release buttons and slide magazine out.

    • Push slide back forward and pull trigger.

  2. Nerf Recon CS-6 O-Ring Replacement, Remove Visible Screws: Schritt 2, Bild 1 von 1
    • Use the Phillips #0 Screwdriver to remove these 9 screws.

    • All screws marked in red are 9.6 mm Phillips #0 screws.

    • Note that left most screw is longer than the rest and is a 18.6 mm Phillips #0 screw.

  3. Nerf Recon CS-6 O-Ring Replacement, Remove Hidden Screws: Schritt 3, Bild 1 von 2 Nerf Recon CS-6 O-Ring Replacement, Remove Hidden Screws: Schritt 3, Bild 2 von 2
    • Pull slide back to reveal more screws.

    • Remove these 2 screws.

    • Push slide forward.

    • Pull trigger to release compression of the main spring.

    • Screws are 9.6 mm Phillips #0.

    • Pulling the trigger will keep spring from launching out of the gun when the two halves are separated.

  4. Nerf Recon CS-6 O-Ring Replacement, Remove Plunger Cap: Schritt 4, Bild 1 von 1
    • Remove the screws on the plunger cap.

    • Tug the plunger cap off.

    • Screws are 9.6 mm Phillips #0.

  5. Nerf Recon CS-6 O-Ring Replacement, Remove Slide Screws: Schritt 5, Bild 1 von 1
    • Remove the 2 screws on the slide.

    • Screws are 9.6 mm Phillips #0.

    • Hold the two halves of the gun together to prevent any springs from launching out.

  6. Nerf Recon CS-6 O-Ring Replacement, Split the Gun in Half: Schritt 6, Bild 1 von 2 Nerf Recon CS-6 O-Ring Replacement, Split the Gun in Half: Schritt 6, Bild 2 von 2
    • Pull the gun apart at the middle seam.

    • Watch for any springs that might launch out.

  7. Nerf Recon CS-6 O-Ring Replacement, Remove Spring: Schritt 7, Bild 1 von 2 Nerf Recon CS-6 O-Ring Replacement, Remove Spring: Schritt 7, Bild 2 von 2
    • Pull the spring out the back of the gun.

  8. Nerf Recon CS-6 O-Ring Replacement, Removing Plunger Guide: Schritt 8, Bild 1 von 1
    • Lift the plunger guide straight up out of the gun.

  9. Nerf Recon CS-6 O-Ring Replacement, Remove Plunger: Schritt 9, Bild 1 von 1
    • Pull the plunger out the back of the gun off of the inner piece.

  10. Nerf Recon CS-6 O-Ring Replacement, Remove  Other Half of Plunger: Schritt 10, Bild 1 von 1
    • Pull the remaining half of the plunger out the back of the gun.

  11. Nerf Recon CS-6 O-Ring Replacement, Removing O-Ring: Schritt 11, Bild 1 von 1
    • Use tweezers to lift the O-Ring out of groove.

    • Replace with new O-Ring.

    • Optional: add a small amount of a lubricant safe for the O-Ring such as petroleum jelly.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

Pam Ruffner

Mitglied seit: 10/20/14

984 Reputation

3 Anleitungen geschrieben

Team

Baylor, Team 8-14, Williams Fall 2014 Mitglied von Baylor, Team 8-14, Williams Fall 2014

BU-WILLIAMS-F14S8G14

3 Mitglieder

6 Anleitungen geschrieben

Ein Kommentar

Ace Hardware 1/16x13/16x1/16 #37 R-80 O-Ring fits

Mr.H - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 3

Letzte 30 Tage: 7

Insgesamt: 2,394