Zum Hauptinhalt wechseln

HP EliteOne 800 G1 Power Supply Replacement

Was du brauchst

  1. HP EliteOne 800 G1 Power Supply Replacement, Removing the Back Cover: Schritt 1, Bild 1 von 3 HP EliteOne 800 G1 Power Supply Replacement, Removing the Back Cover: Schritt 1, Bild 2 von 3 HP EliteOne 800 G1 Power Supply Replacement, Removing the Back Cover: Schritt 1, Bild 3 von 3
    • Place computer with the screen down on a flat surface.

    • Push the two locking latches to the unlocked position.

    • Push the cover toward the top of the computer and lift up.

  2. HP EliteOne 800 G1 Power Supply Replacement, Removing Stand: Schritt 2, Bild 1 von 2 HP EliteOne 800 G1 Power Supply Replacement, Removing Stand: Schritt 2, Bild 2 von 2
    • Press locking latch on the bottom of the base of the stand.

    • Pull the plastic cover off of the stand.

  3. HP EliteOne 800 G1 Power Supply Replacement: Schritt 3, Bild 1 von 2 HP EliteOne 800 G1 Power Supply Replacement: Schritt 3, Bild 2 von 2
    • Use a Torx T15 driver and stick it through the holes on the stand in order to remove the two 12mm screws on the back of the main unit.

    • Tilt stand and lift up to remove it.

  4. HP EliteOne 800 G1 Power Supply Replacement: Schritt 4, Bild 1 von 2 HP EliteOne 800 G1 Power Supply Replacement: Schritt 4, Bild 2 von 2
    • Use a Torx T15 driver to remove the single 10mm screw on the back panel.

    • Pull the back panel toward the bottom of the device to remove it.

  5. HP EliteOne 800 G1 Power Supply Replacement, Power Supply: Schritt 5, Bild 1 von 2 HP EliteOne 800 G1 Power Supply Replacement, Power Supply: Schritt 5, Bild 2 von 2
    • Use a Torx T15 driver to remove the four 10mm screws on the VESA mount cover.

    • Lift up on the VESA mount cover to remove it.

  6. HP EliteOne 800 G1 Power Supply Replacement: Schritt 6, Bild 1 von 1
    • Disconnect the power supply's black and yellow cable from the motherboard.

  7. HP EliteOne 800 G1 Power Supply Replacement: Schritt 7, Bild 1 von 2 HP EliteOne 800 G1 Power Supply Replacement: Schritt 7, Bild 2 von 2
    • Use a Torx T15 driver to remove the two 8mm screws on either side of the power supply.

    • Lift the power supply from the case to remove it.

Abschluss

To reassemble your device, follow these instructions in reverse order.

6 weitere Nutzer:innen haben diese Anleitung absolviert.

Michael Ewing

Mitglied seit: 10/01/15

1.071 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team 1-24, Maness Fall 2015 Mitglied von Cal Poly, Team 1-24, Maness Fall 2015

CPSU-MANESS-F15S1G24

4 Mitglieder

14 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 11

Letzte 30 Tage: 33

Insgesamt: 5,243