Zum Hauptinhalt wechseln

Garmin GPS V Button Pad Replacement

Was du brauchst

  1. Garmin GPS V Button Pad Replacement, Logic Board: Schritt 1, Bild 1 von 3 Garmin GPS V Button Pad Replacement, Logic Board: Schritt 1, Bild 2 von 3 Garmin GPS V Button Pad Replacement, Logic Board: Schritt 1, Bild 3 von 3
    • Orient the GPS V backside up.

    • With a #0 Philips screwdriver, remove six M2x0.4 black screws on the back of the unit.

  2. Garmin GPS V Button Pad Replacement: Schritt 2, Bild 1 von 2 Garmin GPS V Button Pad Replacement: Schritt 2, Bild 2 von 2
    • With the spudger, gently pry the back plate off the unit starting at the corners.

    • Open the back plate about 35°, use the antenna side act like a hinge.

    • Do NOT remove the back plate all the way, there are cables connected to it.

  3. Garmin GPS V Button Pad Replacement: Schritt 3, Bild 1 von 2 Garmin GPS V Button Pad Replacement: Schritt 3, Bild 2 von 2
    • Locate the white 8-pin connector on the logic board and disconnect it.

    • Open the device all the way, making sure to not disconnect the brown antenna wire.

  4. Garmin GPS V Button Pad Replacement: Schritt 4, Bild 1 von 2 Garmin GPS V Button Pad Replacement: Schritt 4, Bild 2 von 2
    • With a #1 Philips screwdriver, remove the silver M2x0.4 screw on the logic board near the brown wire.

    • You may need to rotate the device to get better access to the screw.

  5. Garmin GPS V Button Pad Replacement: Schritt 5, Bild 1 von 3 Garmin GPS V Button Pad Replacement: Schritt 5, Bild 2 von 3 Garmin GPS V Button Pad Replacement: Schritt 5, Bild 3 von 3
    • Locate the ribbon connector on the logic board.

    • With the spudger, gently apply pressure to both sides of the brown connector lock until it pushes out.

    • With the spudger, gently work the ribbon cable out of the connector until it is free.

  6. Garmin GPS V Button Pad Replacement: Schritt 6, Bild 1 von 2 Garmin GPS V Button Pad Replacement: Schritt 6, Bild 2 von 2
    • With the spudger, gently pry out the logic board.

    • Be careful to not disconnect the brown antenna wire as you remove the logic board.

  7. Garmin GPS V Button Pad Replacement: Schritt 7, Bild 1 von 1
    • Locate the brown wire connection on the logic board.

    • Carefully apply heat with the soldering iron while gently pulling on the brown wire.

    • It may take some time to heat the flux up before the wire can be pulled out.

    • Pull brown wire free of the logic board.

  8. Garmin GPS V Button Pad Replacement, Button Pad: Schritt 8, Bild 1 von 3 Garmin GPS V Button Pad Replacement, Button Pad: Schritt 8, Bild 2 von 3 Garmin GPS V Button Pad Replacement, Button Pad: Schritt 8, Bild 3 von 3
    • Gently pry the button pad off of the front plate.

Abschluss

To reassemble your device, follow these instructions in reverse order.

3 weitere Nutzer:innen haben diese Anleitung absolviert.

Connor

Mitglied seit: 01/23/12

194 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team 3-25, Amido Winter 2012 Mitglied von Cal Poly, Team 3-25, Amido Winter 2012

CPSU-AMIDO-W12S3G25

4 Mitglieder

4 Anleitungen geschrieben

Ein Kommentar

Hey, a have an old Garmin GPS III and my problem is that the GPS can not find any satelliters. I have opened back plate and I think its looks ok inside.

What can I do?

Best regards

Christian Tregert

Ctregert@hotmail.com

ChristianTregert - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 2

Letzte 30 Tage: 4

Insgesamt: 1,452