Zum Hauptinhalt wechseln

Dremel 4000 Power Cord Replacement

Was du brauchst

  1. Dremel 4000 Power Cord Replacement, Back Case: Schritt 1, Bild 1 von 2 Dremel 4000 Power Cord Replacement, Back Case: Schritt 1, Bild 2 von 2
    • Start by removing the housing cap by unscrewing it.

    • Next, unscrew the now exposed collet nut while holding down the shaft lock button.

    • To remove the collet nut, you may need to use the small open-end wrench provided with the Dremel.

  2. Dremel 4000 Power Cord Replacement: Schritt 2, Bild 1 von 1
    • Using your hands, carefully remove hanger from casing.

  3. Dremel 4000 Power Cord Replacement: Schritt 3, Bild 1 von 2 Dremel 4000 Power Cord Replacement: Schritt 3, Bild 2 von 2
    • Remove the brush caps (one on each side) by using a flathead screwdriver bit.

    • The brush caps are spring loaded.

  4. Dremel 4000 Power Cord Replacement: Schritt 4, Bild 1 von 1
    • Using the Torx 15 screwdriver tip, remove the 5 screws (12.5 mm) that hold the casing together.

  5. Dremel 4000 Power Cord Replacement: Schritt 5, Bild 1 von 1
    • Use a plastic opening tool to gently wedge apart the hard plastic threads.

  6. Dremel 4000 Power Cord Replacement: Schritt 6, Bild 1 von 1
    • Use your hands to carefully remove the back casing so that none of the components fall out.

  7. Dremel 4000 Power Cord Replacement, Power Cord: Schritt 7, Bild 1 von 2 Dremel 4000 Power Cord Replacement, Power Cord: Schritt 7, Bild 2 von 2
    • To clear access to the electrical assembly, remove the variable speed dial cap and blue power lever, and set them aside.

  8. Dremel 4000 Power Cord Replacement: Schritt 8, Bild 1 von 1
    • Using your fingers, carefully pull the circuit board from the casing. This will make it easier to remove the power cord.

  9. Dremel 4000 Power Cord Replacement: Schritt 9, Bild 1 von 1
    • Each wire is fed through a small opening on the circuit board and held with a flat head screw.

    • Loosen the screw just enough to remove the wire by gently pulling it with your hand.

  10. Dremel 4000 Power Cord Replacement: Schritt 10, Bild 1 von 1
    • Carefully remove both wires from circuit board with your hands.

    • Take careful note of which side has the black wire and which has the white wire.

Abschluss

To reassemble your device, follow these instructions in reverse order.

5 weitere Nutzer:innen haben diese Anleitung absolviert.

John Cobb

Mitglied seit: 01/20/16

1.689 Reputation

4 Anleitungen geschrieben

Team

USF Tampa, Team 15-4, Remmell Spring 2016 Mitglied von USF Tampa, Team 15-4, Remmell Spring 2016

USFT-REMMELL-S16S15G4

4 Mitglieder

13 Anleitungen geschrieben

Ein Kommentar

Super handy guide after my guide dog decided to chew through the cable!

Geoff Palmer - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 4

Letzte 30 Tage: 38

Insgesamt: 5,641