Zum Hauptinhalt wechseln
Englisch
Chinesisch

Apple Watch Series 3 Force Touch 垫圈更换

Grundständige Anleitungen

Bevor diese Anleitung als vollständig übersetzt gilt müssen alle grundständigen Anleitungen übersetzt werden.

Apple Watch Series 2 的屏幕开启指南

Apple Watch Series 3 电池分离 —— 前提条件指南

Informationen zur Anleitung

= Fertig = Unvollständig
This guide shows how to remove and replace the force touchForce Touch gasket in the Apple Watch Series 3. The gasket has adhesive on both sides which is also replaced.
    Use this guide to replace the force touchForce Touch gasket in your Apple Watch Series 3. This guide shows the procedure while leaving the display connected. If you are also replacing the display, refer to [guide|115764|this guide|new_window=true] and replace the force touchForce Touch gasket after having the display removed and before reconnecting the new display. That will makeThis makes it a little easier to position the gasket.

    If Force Touch function works correctly and you just need fresh adhesive to re-seal your display, follow the [guide|116656|adhesive replacement guide] instead.

    The device shown in the photos of this guide is the GPS-only version of the Apple Watch Series 3. There are some minor differences between the GPS and the Cellular versions of the Apple Watch. '''If you have the Cellular version, follow all the written directions closely and pay extra attention to the warnings about discrepancies between the two devices.'''
      Take your e-waste to an [[E-Waste|R2 or e-Stewards certified recycler|new_window=true]].
      Repair didn’t go as planned? Try some [[Troubleshooting Problems After a Repair|basic troubleshooting]], or search our [https://www.ifixit.com/Answers/Device/Apple%20Smartwatch|Answers forum] for help.

      Beschreibe das genaue Ersatzteil oder den Bestandteil des device an dem du arbeitest. Bsp. Akku

      Einen Titel erstellen.

      Diese kurze Zusammenfassung wird nur in den Suchergebnissen angezeigt.

      Gebe Hintergrundinformationen, bevor der Leser mit der Anleitung beginnt.

      Anleitungsschritte

      1. Schritt — Force Touch 垫圈

      使用撬棒的尖端通过从外边缘直接向上撬动力触摸垫圈来断开它。

      2. Schritt

      准备一个iOpener,并将其放在 Force Touch 垫圈的顶部,以软化下面的粘合剂。

      3. Schritt

      用一把镊子剥掉 Force Touch 垫圈。

      4. Schritt

      在棉签上涂抹一点异丙醇(> 90%酒精)或使用清洁垫轻轻去除Force Touch垫圈上残留的任何粘合剂。

      5. Schritt

      翻转手表,使显示屏平放,同时略微抬起外壳。

      6. Schritt

      使用一把镊子小心地从新的Force Touch垫圈底部取下保护膜。

      7. Schritt

      沿对角方向握住 Force Touch 垫圈,将其穿过显示屏。

      8. Schritt

      通过撬棒轻轻按下柔性电缆重新连接。

      9. Schritt

      使用镊子将覆盖电池接口的金属板放回原位。

      10. Schritt

      使用一把镊子轻轻取下 Force Touch 垫圈顶部的保护膜。

      11. Schritt

      对齐显示屏并将其牢牢按在粘合剂上。

      Deine Beiträge sind lizenziert unter der Open-Source Creative Commons Lizenz.