Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 3 : Schritt 1, Bild 2 von 3 : Schritt 1, Bild 3 von 3
    • Open the trunk and locate the tail light compartment behind the rear wheel well.

    • This guide will serve for both brake lights.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 3 : Schritt 2, Bild 2 von 3 : Schritt 2, Bild 3 von 3
    • Squeeze and pull back on the felt-like access panel to expose the tail light assembly.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 3 : Schritt 3, Bild 2 von 3 : Schritt 3, Bild 3 von 3
    • Squeeze down on the top tab of the battery connector. Then, pull the connector out.

    • Be sure to properly disconnect the battery to ensure safety when replacing the bulb.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 3 : Schritt 4, Bild 2 von 3 : Schritt 4, Bild 3 von 3
    • The grey brake light holder is connected to three wires. (Pink, Green, and Black as displayed)

    • Be sure not to pull on the three wires.

    • Twist the holder counter-clockwise using the two protruding tabs. Pull out the holder once unlocked.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 2 : Schritt 5, Bild 2 von 2
    • Twist the dead bulb counter clockwise to unlock it from the holder.

    • Be sure not to squeeze too hard on the light bulb as it may shatter or break.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 2 : Schritt 6, Bild 2 von 2
    • Be sure to place latex gloves on prior to opening and touching the new bulb.

    • Align the new bulb with the notch in the holder. Place bulb inside holder.

    • Gently push the bulb in and simultaneously twist clockwise to lock it into the holder.

Ziellinie

6 weitere Nutzer:innen haben diese Anleitung absolviert.

3 Kommentare

Perfect instructions. Very easy and fast.

jamie swartz - Antwort

Step 5: Twist the dead bulb counter clockwise to unlock it from the holder.

Is incorrect for at least the Canadian model of the Kia Optima. The brake light bulb on the drivers side needs to be pushed in and rotated ~30 degrees counter clockwise to be taken out of the grey bulb holder, I suspect the passenger side is the same.

Secondly for Canada, at least at Canadian Tire the bulb to buy is Sylvania LongLife bulb “2357”

kurt - Antwort

I’m not in Canada so I don’t know the difference between Canadian and American but I had to push the bulb in and turn counter-clockwise to remove. But I did purchase both the Sylvania Longlife bulbs 1157A and 2357 but used 1157a.

Samantha Gibson - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 7

Letzte 7 Tage: 51

Letzte 30 Tage: 290

Insgesamt: 26,688