Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.
Was du brauchst
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Drain gas and chain oil into proper storage containers.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove top cover screws (3) using a #6 flat head screw driver on the chainsaw T-wrench.
-
Loosen the 1/4" nuts holding the bar cover in place using the chainsaw T-wrench.
-
Turn the chain tension adjustment screw two turns counter clockwise.
-
Remove the nuts holding the bar cover in place, and then remove the bar.
-
Remove fly wheel cover using a 5/32" Allen wrench.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Pull the air filter from the housing.
-
Remove the air filter housing using a 8 mm socket.
-
Disconnect the two fuel lines from the carburetor using a narrow, flat-head screw driver.
-
Disconnect the throttle linkage from the carburetor.
-
Lift the choke linkage out of the housing, and then pull the carburetor from the housing.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the four screws holding the diaphragm cover plate, and then remove the plate.
-
Remove the diaphragm and its seal from the carburetor.
-
Remove the screw holding the float set and needle valve.
-
Remove the float set and needle valve.
-
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the screw holding the fuel pump cover in place using the chainsaw T-wrench.
-
Remove the fuel pump gasket and valve.
-
Remove the fuel filter screen.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Remove the adjustment needle retaining clip.
-
Remove both adjustment needles while counting the number of turns required for the removal.
-
Clean and reinstall the needles, turning the same number of turns that were counted in the previous step.
-
Replace the retaining clip.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Align a new fuel pump valve and gasket with the carburetor.
-
Reattach the fuel pump top cover using the chainsaw T-wrench.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Install a new float set and needle valve.
-
Install the float set and needle valve retaining screw.
-
Place a new diaphragm and seal in position.
-
Replace the diaphragm cover and the four retaining screws.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Attach the fuel lines and the throttle linkage to the carburetor.
-
The line coming directly from the fuel tank connects to the fuel pump inlet.
-
The line coming from the external primer bulb goes to the diaphragm inlet.
-
Reinstall the throttle linkage.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Reinstall the air filter housing, securing it with the 8 mm nuts.
-
Place the air filter back into the housing.
-
-
Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!
-
Place the top cover back in position and secure it using the flat-head screw driver.
-
Place the fly wheel cover on and secure it using the 5/32'' Allen wrench.
-
Place the bar, chain, and cover back on. Secure the cover with the two cover nuts and the socket wrench that is included on the T-wrench.
-
Rückgängig: Ich habe diese Anleitung nicht absolviert.
Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.