Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 3 : Schritt 1, Bild 2 von 3 : Schritt 1, Bild 3 von 3
    • To prevent injury, make sure the laptop is unplugged before removing the battery.

    • To prevent data loss, make sure the laptop has fully shut down before removing the battery.

    • Pull the switch on the back of laptop in the direction of the arrow.

    • If done correctly the battery should pop out. Lift the battery to remove it.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 2 : Schritt 2, Bild 2 von 2
    • Use the screwdriver to remove the rubber cap on the top of the backplate.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 3 : Schritt 3, Bild 2 von 3 : Schritt 3, Bild 3 von 3
    • Remove the screw that was uncovered.

    • Pull the backing plate away from the laptop.

    • This will take a fair amount of force.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 3 : Schritt 4, Bild 2 von 3 : Schritt 4, Bild 3 von 3
    • Remove the four screws located in the corners of the metal bracket.

    • Three of the four screws are the same size. The exception is the bottom left screw, which is significantly shorter. Make sure to put the short screw where it belongs when re-assembling.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 3 : Schritt 5, Bild 2 von 3 : Schritt 5, Bild 3 von 3
    • Push the hard drive away from the center until fully disconnected.

    • Lift the hard drive from the bottom right tab to remove it from the laptop.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 3 : Schritt 6, Bild 2 von 3 : Schritt 6, Bild 3 von 3
    • Remove the four screws on the side of the hard drive and bracket.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 2 : Schritt 7, Bild 2 von 2
    • Remove the hard drive from the bracket.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 2 : Schritt 8, Bild 2 von 2
    • Insert the new hard drive into the bracket.

Ziellinie

8 weitere Nutzer:innen haben diese Anleitung absolviert.

Team

Cal Poly, Team 14-6, Green Fall 2015 Mitglied von Cal Poly, Team 14-6, Green Fall 2015

CPSU-GREEN-F15S14G6

5 Mitglieder

6 Anleitungen geschrieben

2 Kommentare

That’s not rocket science - How to clone the disk properly? that’s the part I can’t manage… Any freeware clone software that actually WORKS and is not just a dumb backup software…?

Günther Haschberger - Antwort

The free version of Minitool Partition Wizard is very good.

Edward Falk -

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 2

Letzte 30 Tage: 24

Insgesamt: 14,084