Einleitung

Replacing your display will give you a fresh new screen when your old one is not functioning properly.

Lay the monitor on a flat surface so that the back is facing up.
  • Lay the monitor on a flat surface so that the back is facing up.

Kommentar hinzufügen

Grab the hinge cover with both hands on either side of the stand. Squeeze inwards with your thumbs and fingers and lift up to remove the hinge cover.
  • Grab the hinge cover with both hands on either side of the stand.

  • Squeeze inwards with your thumbs and fingers and lift up to remove the hinge cover.

Kommentar hinzufügen

Remove the four 12.1 mm Phillips #2 screws that hold the stand to the monitor. Support the monitor while removing the screws to prevent the monitor from falling.
  • Remove the four 12.1 mm Phillips #2 screws that hold the stand to the monitor.

  • Support the monitor while removing the screws to prevent the monitor from falling.

  • Lift up to detach the stand.

Kommentar hinzufügen

Remove the five 9.5 mm Phillips #2 screws located around the perimeter of the monitor. Remove the five 9.5 mm Phillips #2 screws located around the perimeter of the monitor.
  • Remove the five 9.5 mm Phillips #2 screws located around the perimeter of the monitor.

Kommentar hinzufügen

Starting at the corner of the monitor, wedge the small plastic opening tool between the back cover and the display bezel. Tilt the plastic opening tool up to separate the back cover from the display bezel. Continue around the perimeter of the monitor until the display bezel comes off.
  • Starting at the corner of the monitor, wedge the small plastic opening tool between the back cover and the display bezel.

  • Tilt the plastic opening tool up to separate the back cover from the display bezel.

  • Continue around the perimeter of the monitor until the display bezel comes off.

  • A reasonable amount of force is necessary to detach the back cover from the display bezel.

Kommentar hinzufügen

Reposition the monitor so that the back is facing up. Grab the corners of the monitor and jiggle them upwards to detach the back cover from the inside of the monitor.
  • Reposition the monitor so that the back is facing up.

  • Grab the corners of the monitor and jiggle them upwards to detach the back cover from the inside of the monitor.

  • Lift the back cover up.

Kommentar hinzufügen

Remove the two 5.7 mm Phillips #2 screws located on either side of the EMI shield. Remove the two 5.7 mm Phillips #2 screws located on either side of the EMI shield.
  • Remove the two 5.7 mm Phillips #2 screws located on either side of the EMI shield.

Kommentar hinzufügen

Using a nut driver (or if necessary, needle-nose pliers), remove the two nuts on either side of the VGA input. Using a nut driver (or if necessary, needle-nose pliers), remove the two nuts on either side of the VGA input.
  • Using a nut driver (or if necessary, needle-nose pliers), remove the two nuts on either side of the VGA input.

Kommentar hinzufügen

Grab the metal casing by the sides and slide it down towards the bottom of the monitor. Lift up to remove the metal casing. Beware, metal casing is sharp!
  • Grab the metal casing by the sides and slide it down towards the bottom of the monitor.

  • Lift up to remove the metal casing.

  • Beware, metal casing is sharp!

Kommentar hinzufügen

Remove the three gold 7.5 mm Phillips #2 screws and one silver 8.3 mm Phillips #2 screw from the power supply. Remove the three gold 7.5 mm Phillips #2 screws and one silver 8.3 mm Phillips #2 screw from the power supply.
  • Remove the three gold 7.5 mm Phillips #2 screws and one silver 8.3 mm Phillips #2 screw from the power supply.

Kommentar hinzufügen

Remove the two pieces of yellow tape on the left side of the power supply. Remove the two pieces of yellow tape on the left side of the power supply. Remove the two pieces of yellow tape on the left side of the power supply.
  • Remove the two pieces of yellow tape on the left side of the power supply.

Kommentar hinzufügen

Remove the four little white clips located underneath the pieces of tape by lifting up on their left side. Remove the four little white clips located underneath the pieces of tape by lifting up on their left side.
  • Remove the four little white clips located underneath the pieces of tape by lifting up on their left side.

Kommentar hinzufügen

With the needle-nose pliers, remove the four display connectors by pulling directly left. With the needle-nose pliers, remove the four display connectors by pulling directly left. With the needle-nose pliers, remove the four display connectors by pulling directly left.
  • With the needle-nose pliers, remove the four display connectors by pulling directly left.

Kommentar hinzufügen

Remove the display cable located at the top of the circuit board by pulling it out towards the top of the monitor. Remove the display cable located at the top of the circuit board by pulling it out towards the top of the monitor. Remove the display cable located at the top of the circuit board by pulling it out towards the top of the monitor.
  • Remove the display cable located at the top of the circuit board by pulling it out towards the top of the monitor.

Kommentar hinzufügen

Turn the monitor on its side so that the power supply and circuit board are facing to the right Remove the two 6.6 mm Phillips #2 screws located on both sides of the metal casing (four screws total). Remove the two 6.6 mm Phillips #2 screws located on both sides of the metal casing (four screws total).
  • Turn the monitor on its side so that the power supply and circuit board are facing to the right

  • Remove the two 6.6 mm Phillips #2 screws located on both sides of the metal casing (four screws total).

Kommentar hinzufügen

Set the monitor back down so that the power supply and circuit board are facing you. Feed all four of the connector wires down through the metal casing.
  • Set the monitor back down so that the power supply and circuit board are facing you.

  • Feed all four of the connector wires down through the metal casing.

Kommentar hinzufügen

Grab the sides of the metal casing and lift up. Turn the display over to see the front; you are ready replace the broken display with a new one! Turn the display over to see the front; you are ready replace the broken display with a new one!
  • Grab the sides of the metal casing and lift up.

  • Turn the display over to see the front; you are ready replace the broken display with a new one!

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

3 weitere Nutzer haben diese Anleitung absolviert.

Keith

Mitglied seit 06.10.2011

246 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team 20-26, Maness Fall 2011 Mitglied von Cal Poly, Team 20-26, Maness Fall 2011

CPSU-MANESS-F11S20G26

4 Mitglieder

7 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 1

Letzte 7 Tage: 16

Letzte 30 Tage: 74

Insgesamt: 5,676