Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 3 : Schritt 1, Bild 2 von 3 : Schritt 1, Bild 3 von 3
    • With laptop closed, turn screenside down and remove the battery.

    • Unscrew covers and remove HDD.

    • Unscrew cover and remove RAM.

    • Unscrew and remove cover for fan.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 1
    • Turn laptop so that hinges are closest to you and remove screw from rear of each hinge.

    • Remove screws securing bottom case to logic board. (It won't come off just yet though)

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 3 : Schritt 3, Bild 2 von 3 : Schritt 3, Bild 3 von 3
    • Turn laptop over and open the screen fully. Take care as the screen is still connected to the logic board via black cable on right hinge.

    • Use a spudger to release the silver and black plastic cover that forms the hinge covers. Start at one side nearest a hinge and work along the rear of the case, there are 5 tabs to release along the keyboard edge.

    • Disconnect LCD cable by lifting straight upwards using the black plastic tabs on the top of the LCD connector. You may need to use a spudger to loosen the connection along the uppermost edge-not along the logicboard.

    • Remove 2 screws from left and right hinges.

    • Remove 2 screws securing topcase to rear of battery tray.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 3 : Schritt 4, Bild 2 von 3 : Schritt 4, Bild 3 von 3
    • Remove 2 screws securing power board to logicboard.

    • Lift LCD screen from bottom case.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 2 : Schritt 5, Bild 2 von 2
    • Remove 2 screws securing the keyboard to case.

    • Use a spudger to release tabs on all 4 sides of the keyboard. Do not pull keyboard up too far as the trackpad and keyboard flex cables are still attached to the logicboard.

    • Place ducks in sink, make sure to disinfect sink afterwards.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 3 : Schritt 6, Bild 2 von 3 : Schritt 6, Bild 3 von 3
    • Do not pull keyboard upwards as it is still attached to logicboard.

    • Flip keyboard over to cover trackpad. Disconnect keyboard.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 3 : Schritt 7, Bild 2 von 3 : Schritt 7, Bild 3 von 3
    • Disconnect trackpad.

    • Use a spudger to ease topcase free of bottom case. Slide topcase toward trackpad and then lift up. Resistance can be felt from magnets on topcase.

    • Your laptop should now look like this; middle photo is the remaining logicboard and bottom case, the last photo is the topcase cover.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 3 : Schritt 8, Bild 2 von 3 : Schritt 8, Bild 3 von 3
    • Remove logicboard screws.

    • Remove the 2 screws securing the modem.

    • Disconnect wire from the modem to the logicboard.

    • Disconnect the speaker wire form the logicboard.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 1
    • Use hex no.5 tool to unscrew 2 bolts from port next ac-in jack.

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 10, Bild 1 von 3 : Schritt 10, Bild 2 von 3 : Schritt 10, Bild 3 von 3
    • Slide DVD drive from logicboard frame.

    • Slide logicboard toward trackpad and then lift out of logicboard frame. The logicboard has a pin connection to the battery tray preventing direct lifting of the logicboard.

    • Last 2 photo's show top of logicboard and underside of logicboard.

Ziellinie

22 weitere Nutzer:innen haben diese Anleitung absolviert.

pollytintop

Mitglied seit: 06/09/10

77.153 Reputation

5 Anleitungen geschrieben

Team

Master Techs Mitglied von Master Techs

Community

321 Mitglieder

1.466 Anleitungen geschrieben

3 Kommentare

superb thanx thanx thanx

thushararoshanperera - Antwort

Great start, but this is not my 1410 and there is no selection for other models. The one I have is much smaller. Mine is model 1410-2817.

William Nelson - Antwort

Great effort but my model does not mach, much smaller, 1410-2817.

William Nelson - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 8

Letzte 30 Tage: 54

Insgesamt: 17,160