Einleitung

After removing the top case, it is easy to get to the internal wireless card.

Ersatzteile

Kein Ersatzteil erforderlich.

Turn the netbook upside down with the battery at the top, away from you.
  • Turn the netbook upside down with the battery at the top, away from you.

Kommentar hinzufügen

Unlock the battery by sliding the switch located near the left hinge to the left "unlocked" position.
  • Unlock the battery by sliding the switch located near the left hinge to the left "unlocked" position.

Kommentar hinzufügen

Slide the latch located on the opposite hinge from the lock while pushing the battery up.
  • Slide the latch located on the opposite hinge from the lock while pushing the battery up.

Kommentar hinzufügen

Gently loosen the two Phillips #0 screws in the small panel that covers the wireless card.
  • Gently loosen the two Phillips #0 screws in the small panel that covers the wireless card.

    • These screws are built into the panel and aren't meant to be completely removed.

Kommentar hinzufügen

Lift up the panel and remove it from the case.
  • Lift up the panel and remove it from the case.

Kommentar hinzufügen

Disconnect the two antenna cables from the left side of the wireless card.
  • Disconnect the two antenna cables from the left side of the wireless card.

Kommentar hinzufügen

Remove the single 3.9 mm Phillips #1 screw from the bottom left of the wireless card.
  • Remove the single 3.9 mm Phillips #1 screw from the bottom left of the wireless card.

Kommentar hinzufügen

Gently lift up the left side of the wireless card and slide the card out of its socket.
  • Gently lift up the left side of the wireless card and slide the card out of its socket.

mi lap NO tiene wireless card

gustavo cordova - Antwort

Turn the netbook over and open the display so that the keyboard is facing you.
  • Turn the netbook over and open the display so that the keyboard is facing you.

Kommentar hinzufügen

There are three tabs located on the top of the keyboard. Start with the spudger pointing towards the display and pry up to push each tab off the keyboard. As you move to the next tab, ensure the previous tab doesn't reset itself.
  • There are three tabs located on the top of the keyboard.

  • Start with the spudger pointing towards the display and pry up to push each tab off the keyboard.

  • As you move to the next tab, ensure the previous tab doesn't reset itself.

Kommentar hinzufügen

Lift top of keyboard up. If it doesn't lift easily, there may be tabs on the sides - use the tool to ease them aside and/or shift the keyboard from side to side. There is a short ribbon cable connecting the keyboard to the netbook.
  • Lift top of keyboard up. If it doesn't lift easily, there may be tabs on the sides - use the tool to ease them aside and/or shift the keyboard from side to side.

  • There is a short ribbon cable connecting the keyboard to the netbook.

Kommentar hinzufügen

Disconnect the ribbon by lifting the black plastic hinge and removing the clear blue cable. Disconnect the ribbon by lifting the black plastic hinge and removing the clear blue cable.
  • Disconnect the ribbon by lifting the black plastic hinge and removing the clear blue cable.

Kommentar hinzufügen

Close the display and turn the ZG5 over so that the battery compartment faces away from you.
  • Close the display and turn the ZG5 over so that the battery compartment faces away from you.

Kommentar hinzufügen

Remove three 5.8 mm Phillips #0 screws from the bottom of the case Remove three 3.9 mm  Phillips #1 screws  from the battery compartment.
  • Remove three 5.8 mm Phillips #0 screws from the bottom of the case

  • Remove three 3.9 mm Phillips #1 screws from the battery compartment.

  • Remove two 5.8 mm Phillips #0 screws from underneath the feet near the hinges.

Kommentar hinzufügen

Turn the netbook back over and open the display with the keyboard cavity facing you.
  • Turn the netbook back over and open the display with the keyboard cavity facing you.

Kommentar hinzufügen

Flip up the retaining flap on the trackpad ribbon cable ZIF connector. Using the blue tab, pull the trackpad ribbon cable from its socket on the motherboard. Using the blue tab, pull the trackpad ribbon cable from its socket on the motherboard.
  • Flip up the retaining flap on the trackpad ribbon cable ZIF connector.

  • Using the blue tab, pull the trackpad ribbon cable from its socket on the motherboard.

Kommentar hinzufügen

Remove the five black 4.7 mm Phillips #0 screws from the metal casing. Remove the single silver 4.3 mm Phillips #00 screw from the right side of  the metal casing.
  • Remove the five black 4.7 mm Phillips #0 screws from the metal casing.

  • Remove the single silver 4.3 mm Phillips #00 screw from the right side of the metal casing.

Kommentar hinzufügen

Starting at the red rings along the hinge, insert a spudger or plastic opening tool into the seam between the two halves of the case. Slide the spudger toward the front of the device, releasing the small clips that hold down the top case.
  • Starting at the red rings along the hinge, insert a spudger or plastic opening tool into the seam between the two halves of the case.

  • Slide the spudger toward the front of the device, releasing the small clips that hold down the top case.

  • Gently lift off the top case.

Kommentar hinzufügen

Disconnect the two antenna cables from the right side of the wireless card.
  • Disconnect the two antenna cables from the right side of the wireless card.

Kommentar hinzufügen

Remove the single 3.9 mm Phillips #1 screw from the wireless card.
  • Remove the single 3.9 mm Phillips #1 screw from the wireless card.

Kommentar hinzufügen

Gently pull the wireless card to the right and slide it out of its socket.
  • Gently pull the wireless card to the right and slide it out of its socket.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

3 weitere Nutzer haben diese Anleitung absolviert.

Doug Gallatin

Mitglied seit 05.10.2010

5.645 Reputation

10 Anleitungen geschrieben

Team

Cal Poly, Team 7-49, Amido Fall 2010 Mitglied von Cal Poly, Team 7-49, Amido Fall 2010

CPSU-AMIDO-F10S7G49

5 Mitglieder

10 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 3

Letzte 7 Tage: 18

Letzte 30 Tage: 68

Insgesamt: 22,270