Einleitung

Step by step guide showing how to replace the CPU fan. This should help prevent the computer from overheating and randomly shutting off.

  1. Use the pointed end of the spudger to slide the battery lock until the battery pops loose.
    • Use the pointed end of the spudger to slide the battery lock until the battery pops loose.

    Kommentar hinzufügen

  2. Slide the battery out of the battery slot.
    • Slide the battery out of the battery slot.

    Kommentar hinzufügen

    • Unscrew the two RAM 6mm cover screws.

    • Use a PH1 screw bit.

    Kommentar hinzufügen

    • Pop the RAM cover off.

    • Use the plastic opening tool.

    Kommentar hinzufügen

    • Use either the spudger or your fingers to pinch the clips away from the RAM chip on either side of each chip.

      • The chip should pop up.

      • The clips break easily.

    • Slide the RAM memory chips out of the slots.

    Kommentar hinzufügen

    • Remove the two 6mm PH1 screws from the bottom of the laptop.

    Kommentar hinzufügen

    • Use the spudger, push the two tabs, located in the battery slot, through their slots to release the keyboard.

      • Do this with the computer slightly open for ease.

    Kommentar hinzufügen

    • Open the laptop.

    • Start top of the keyboard and use the opening tool to pop the remaining tabs around the keyboard loose.

    • The keyboard can be flipped onto its face once removed.

    Kommentar hinzufügen

    • Use the spudger and slide the grey tabs on either side of the keyboard wires away from the white plastic.

    Kommentar hinzufügen

    • Disconnect the keyboard by pulling the blue tape on the wire strip.

    Kommentar hinzufügen

    • Remove the five 6mm PH1 screws beneath the keyboard.

    Kommentar hinzufügen

    • Use the spudger to pop the gray tab up and away from the far left wire strip.

    • Disconnect the wire strip by pulling the blue tab loose.

    Kommentar hinzufügen

    • Use the spudger to pop the white tab up away from the wire strip located at the top left corner of the mouse pad.

    • Disconnect the wire strip by pulling the blue tab.

    Kommentar hinzufügen

    • Close the laptop.

    • Remove the remaining 18 6mm PH1 screws from the bottom cover of the laptop.

    Kommentar hinzufügen

    • Use the opening tool to separate the back of the laptop from the inside cover.

    • Open the computer and remove the inside cover.

    Kommentar hinzufügen

    • Lift the HDD out of the base and use the opening tool to disconnect the HDD from the motherboard wire.

    Kommentar hinzufügen

    • Slide the optical disc drive out of the slot to disconnect it from the motherboard.

    • Unscrew the main 3.5mm PH1 screw from the motherboard.

    Kommentar hinzufügen

    • Unscrew the 3.5mm PH1 screw from the Wireless Lan chip.

    • Use the opening tool to pop both wires off of the Wireless Lan chip.

    • Pull the Wirelss Lan Chip to remove it from the motherboard.

    Kommentar hinzufügen

    • Pull the tape covering the wires for the Wireless Lan chip up.

    • Pull the black and white wires loose.

    Kommentar hinzufügen

    • Pull up the tape securing the optical wires to the motherboard.

    • Disconnect the wire plug-in from the motherboard.

    Kommentar hinzufügen

    • Unscrew the 3.5mm PH1 screw securing the optical disk drive to motherboard connector.

    • Pull the connector to disconnect it from the motherboard.

    Kommentar hinzufügen

    • Flip the motherboard up towards the screen to access the underside.

      • There are still wires connected to the motherboard.

    Kommentar hinzufügen

    • Use the spudger to disconnect the remaining three wires from the motherboard.

    • Once the wires are disconnected, the motherboard is completely disconnected from the laptop frame.

    Kommentar hinzufügen

    • Unscrew the three PH1 screws connecting the CPU fan to the motherboard.

    • The three screws are permanently attached to the CPU fan assembly.

    Kommentar hinzufügen

    • On the side opposite the CPU fan screws, pull loose the tape securing the fan assembly to the motherboard.

      • This is the same tape that covered the Wireless Lan chip black and white wires.

    • The CPU fan can now be separated from the motherboard.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Josh Focht

Mitglied seit 29.01.2018

241 Reputation

2 Anleitungen geschrieben

Team

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 2

Insgesamt: 84