Was du brauchst
-
-
Wir legen das Gerät mit der Vorderseite nach unten und nehmen die untere Gummiabdeckung ab. Es ist besser, an einer Ecke zu beginnen.
-
Wir erhitzen den Deckel, um ihn abnehmen zu können. Es braucht viel Klebstoff unter der gesamten Oberfläche. Seien Sie geduldig und sehr vorsichtig.
-
-
-
Wir entfernen die 10 Kreuzschlitzschrauben #00, die die untere Metallstütze der Time Capsule halten.
-
Wir öffnen nach links und lassen die Netzwerkanschlüsse auf dieser Seite. Nicht ganz öffnen, damit das Lüfterkabel nicht beschädigt wird.
thanks for doing this guide.
1. remove hash sign (#) before the 10. “Remove the 10 Phillips...
2. second bullet - “Do not open all the way to avoid…
I agree!
Good Job!
-
-
-
Löse vorsichtig mit der Spudgerspitze den Lüfteranschluss und entferne die metallene untere Abdeckung.
-
-
-
-
Wir können den Temperatursensor auf der Oberfläche der Festplatte beobachten.
-
Wir ziehen vorsichtig das Klebeband ab, das den Temperatursensor bedeckt.
-
-
-
Wir heben die Festplatte ein wenig an, ohne zu stark zu ziehen, um die Strom- und Datenanschlüsse der Festplatte nicht zu beschädigen. Wir entfernen den Stromanschluss von der Festplatte
-
Wir entfernen den Datenstecker von der Festplatte.
-
-
-
Sobald wir die Festplatte aus der Time Capsule haben, entfernen wir die 4 Säulen mit Phillips #00 Köpfen und legen sie in die neue Einheit.
A #1 Philips works a lot better on these
Not gonna lie, I used a eye glasses repair kit screwdriver.
Hello there, is this SATA II or SATA III HDD?
-
Befolge die Anweisungen in umgekehrter Reihenfolge, um dein Gerät wieder zusammenzusetzen.
Befolge die Anweisungen in umgekehrter Reihenfolge, um dein Gerät wieder zusammenzusetzen.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
38 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
12 Kommentare
I replaced a dead drive in about 30 mins following these instructions. The steps are clear, straight forward and the photos were extremely helpful. Many thanks as I now have a renovated AirPort Time Capsule.
I just replaced the 2 TB WDC Green with a WD Red Pro 4 TB with this guide in less than 30 min. Except for the fan cable it was a cake walk.
Successfully upgraded my A1409 to a Western Digital - WD100PURZ - 5400 RPM Class SATA 6 Gb/s 256MB Cache 3.5. There are two additional steps: (a), there is a rubber strip around the original drive that reduces noise and protects the drive, gently remove from the original drive and place on the new drive; (b) once the rubber strip is on the drive, it is hard to get into place, angle the drive towards the connector side, and press in.
Hi. Is it possible to upgrade this to an SSD?
Yes, you could also use an SSD, just follow the same procedure.
Idrees -
How to Clone or Copy data to a new hard drive?
It's not formatting the installed WD Red WD101EFAX which I've installed. Any help or suggestions?
Take it out then Try formatting it on Mac and then re-install it and try formatting again.
This was super helpful. I used the microwaveable ifixit gel opener to loosen the glue on the rubber pad. Starting from one side and wedging a metal pry tool underneath as I moved about 1-2 inches at a time, reheating every few inches. Worked perfectly, no rips or tears on the rubber.
I mounted an SSD with VHB tape left over from another project, it holds drive securely against the side of the drive mount.
During reassembly, the glue on the back is still tacky enough to hold the rubber on, but a few small pieces of VHB tape in the corners helped.
It’s actually useful again, and very handy for my legacy Macs. Thanks for posting this!
The rubber tears real easy with age so carefully work your way inwards from each corner.
AndreasT - Antwort
Just happen to me :/
Ben Capehart -