Zum Hauptinhalt wechseln

Diese Anleitung enthält neuere Änderungen. Wechsel zur neuesten unüberprüften Version.

Apple Studio Display M2454 Main Computer Cable Replacement

Was du brauchst

  1. Apple Studio Display M2454 Main Computer Cable Replacement, Main Computer Cable: Schritt 1, Bild 1 von 1
    • First, the back panel needs to be removed to access the cable connectors.

    • Locate the three 2mm hex screws located on the top of the stand and remove them.

    • Now locate and remove the four 2mm hex screws on the corners of the back panel.

    • Now remove the back panels while pulling the cable through them without damaging either part.

  2. Apple Studio Display M2454 Main Computer Cable Replacement: Schritt 2, Bild 1 von 1
    • Remove the metal back plate by using the #2 philips head screwdriver and removing the top screw.

    • Now remove the two other philips screws located below the cable with the philips head screwdriver.

    • With all the screws removed, push the metal plate towards the bottom of the monitor to release the clips holding it to the monitor.

    • Pull the metal plate away.

  3. Apple Studio Display M2454 Main Computer Cable Replacement: Schritt 3, Bild 1 von 1
    • Locate and remove the four #2 phillips screws located on the corners of the stand bracket, using the phillips head screwdriver.

    • Pull bracket away from monitor.

  4. Apple Studio Display M2454 Main Computer Cable Replacement: Schritt 4, Bild 1 von 1
    • Remove the cable hold-down with #2 phillips head screwdriver.

  5. Apple Studio Display M2454 Main Computer Cable Replacement: Schritt 5, Bild 1 von 1
    • Remove the screw at the bottom of the plastic bracket, using #2 phillips head screwdriver.

    • Pull the plastic bracket free.

    • Note the plastic pegs lining the bracket up with the monitor.

  6. Apple Studio Display M2454 Main Computer Cable Replacement: Schritt 6, Bild 1 von 1
    • Remove tape holding down the white connector to the LCD main board.

  7. Apple Studio Display M2454 Main Computer Cable Replacement: Schritt 7, Bild 1 von 1
    • With tape removed, the connections on the LCD main board can be disconnected.

    • First, remove the single hold-down using the philips head screwdriver.

    • Now locate the three connections the main cable makes with the monitor. Two are on the LCD Main Board and one other to the side.

    • Disconnect the white connector to the LCD main board by gently lifting tab with small pry tool and pulling out.

    • The tabs can easily break off, be extra careful

    • Disconnect the black connector to the LCD main board by pressing the tab and pulling out.

  8. Apple Studio Display M2454 Main Computer Cable Replacement: Schritt 8, Bild 1 von 1
    • Now remove the connection not on the LCD Main Board by pulling back the tape holding the wires down first.

    • Remove the connector by hand.

  9. Apple Studio Display M2454 Main Computer Cable Replacement: Schritt 9, Bild 1 von 1
    • Finally, the main cable can be replaced by pulling the old cable away and repeating the previous steps in reverse with a new, working main cable.

Ziellinie

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

Dylan Perry

Mitglied seit: 01/20/10

177 Reputation

5 Anleitungen geschrieben

Team

Cal Poly, Team 13-27, Maness Winter 2010 Mitglied von Cal Poly, Team 13-27, Maness Winter 2010

CPSU-MANESS-W10S13G27

4 Mitglieder

9 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 1

Letzte 30 Tage: 12

Insgesamt: 5,598