Repariere deine Sachen Community Store

Diese Anleitung enthält neuere Änderungen. Wechsel zur neuesten unüberprüften Version.

Apple TV 1st Generation Fan Replacement

Einleitung

Replace the fan in your Apple TV 1st Generation.

Was du brauchst

  1. Apple TV 1st Generation Fan Replacement, Lower Case: Schritt 1, Bild 1 von 1

    • Flip the Apple TV over so that the bottom of the unit is facing up.

    • You need to remove the rubber base to get access to the screws.

    • Starting at one side of the device, use a hairdryer or a heat gun to soften the adhesive holding the rubber base in place.

    • The rubber base will be hot after heating, take extreme caution while proceeding to avoid personal injury.

    • While the adhesive is still warm, peel the bottom of the rubber base upwards to detach it from the metal plate.

    • The rubber base can tear if the adhesive hasn't been softened enough.

    • Repeat the procedure described above until the rubber base has been completely removed.

    Übersetzen

  2. Apple TV 1st Generation Fan Replacement: Schritt 2, Bild 1 von 1

    • Remove the four T10 Torx screws that secure the lower case to the upper case.

    Übersetzen

  4. Apple TV 1st Generation Fan Replacement: Schritt 3, Bild 1 von 1

    • Carefully lift the lower case from the upper case enough to allow access to the internals of the Apple TV.

    • Be aware that the hard drive is physically attached to the lower case and that a ribbon cable runs from the drive to the logic board in the upper case.

    Übersetzen

  5. Apple TV 1st Generation Fan Replacement: Schritt 4, Bild 1 von 2 Apple TV 1st Generation Fan Replacement: Schritt 4, Bild 2 von 2

    • Carefully pull the hard drive data cable straight up from its socket on the logic board.

    • During reassembly, make sure the hard drive data cable is firmly seated in its socket on the logic board; otherwise, during boot-up you will see a flashing question mark "?".

    Übersetzen

  6. Apple TV 1st Generation Fan Replacement, Fan: Schritt 5, Bild 1 von 1

    • The fan is held in place by three rubber posts.

    • Using a pair of tweezers, squeeze the top of each post and push the post down into the hole. Repeat for all three posts.

    • During reinstallation, it helps to lubricate the rubber posts. Try weaving a string through the holes in the posts to pull them up through the mounting points.

    • Do not excessively pull on the posts, as they may rip.

    Übersetzen

  7. Apple TV 1st Generation Fan Replacement: Schritt 6, Bild 1 von 1

    • Using a pair of tweezers, pull the fan connector straight up from its socket on the logic board.

    • Lift and remove the fan out of the upper case.

    Übersetzen
Abschluss

To reassemble your device, follow these instructions in reverse order.

4 weitere Nutzer:innen haben diese Anleitung absolviert.

Autor:in

mit 11 anderen Mitwirkenden

ropel

Mitglied seit: 11/11/09

113 Reputation

2 Anleitungen geschrieben

Auszeichnungen: 8

+ 5 weitere Auszeichnungen

Team

Cal Poly, Team 18-5, Maness Fall 2009 Mitglied von Cal Poly, Team 18-5, Maness Fall 2009

CPSU-MANESS-F09S18G5

5 Mitglieder

6 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 3

Letzte 30 Tage: 7

Insgesamt: 11,829