Zum Hauptinhalt wechseln

Einleitung

During this guide you will need some solder skills to repair the product. If you don't have any experiences in soldering, take a look at the How to Solder and Desolder Connections guide. Make sure you have all the tools that's needed to desolder en solder. Be aware of the fumes—do this in a well ventilated room!

  1. Unscrew the four Phillips screws on the backside of the docking system. The screws are located quite deep. Make sure you have a long screwdriver to be able to reach the screws. Be aware of the plastic threads. Using too much force can tear this up.
    • Unscrew the four Phillips screws on the backside of the docking system.

    • The screws are located quite deep. Make sure you have a long screwdriver to be able to reach the screws.

    • Be aware of the plastic threads. Using too much force can tear this up.

  2. Separate the housing in two parts.
    • Separate the housing in two parts.

    • The dock connector is slid in two parts on the top of the system, make sure you slide the two housing parts in this line of direction.

    • The two parts are glued on the sides of the speakers. Use some force to separate the two housing parts.

    • The internal parts are still connected to each other. Don't pull the housing parts too far from each other.

  3. Slide the dock connector out of the housing part.
    • Slide the dock connector out of the housing part.

  4. Unscrew the three screws using a Phillips #2 screwdriver to remove the T-shaped circuit board holder.
    • Unscrew the three screws using a Phillips #2 screwdriver to remove the T-shaped circuit board holder.

  5. Remove the T-shaped circuit board holder.
    • Remove the T-shaped circuit board holder.

  6. Remove the circuit board from the housing part.
    • Remove the circuit board from the housing part.

    • The circuit board is still connected to another circuit board with a cable.

  7. Disconnect the 5-pin connector between the two circuit boards.
    • Disconnect the 5-pin connector between the two circuit boards.

    • The connectors are tightly connected. Hold the other circuit board to prevent it from breaking while disconnecting the 5-pin connector.

  8. Look how the cables are oriented. Take a picture with your phone. It's easier to look it up than recalling your memory.
    • Look how the cables are oriented.

    • Take a picture with your phone. It's easier to look it up than recalling your memory.

  9. Trigger the desoldering pump before heating the solder.
    • Trigger the desoldering pump before heating the solder.

  10. Heat up the solder.
    • Heat up the solder.

    • If you don't want to damage your workspace, it's probably handy to place something underneath.

    • The circuit board will be getting hot. To make it more stable you can clamp it in a vise or alligator clips.

    • The heated solder tends to fume—do not inhale this! Do this in a well ventilated room.

  11. If the solder becomes fluid, keep the desoldering pump near the solder. Push the button on the desoldering pump to suck the solder.
    • If the solder becomes fluid, keep the desoldering pump near the solder.

    • Push the button on the desoldering pump to suck the solder.

    • Solder will solidify fast, so you need to act quickly.

  12. Strip the cables with a wire stripper.
    • Strip the cables with a wire stripper.

  13. Check if the cable is in the right position. Heat up the contact point on the circuitboard.
    • Check if the cable is in the right position.

    • Heat up the contact point on the circuitboard.

    • If the contact point is hot enough, you can add a little bit of solder.

    • Don't inhale the fumes.

Abschluss

Om het apparaat weer te monteren, volg je deze instructies in omgekeerde volgorde vanaf stap 7.

Anoniem

Mitglied seit: 08.03.2017

12 Reputation

1 Anleitung geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzten 24 Stunden: 0

Letzten 7 Tage: 1

Letzten 30 Tage: 2

Insgesamt: 253