Zum Hauptinhalt wechseln

Austausch des rechten Nintendo Switch Joy-Con Gehäuse

Was du brauchst

  1. Austausch des rechten Nintendo Switch Joy-Con Gehäuse, Rechtes Joy-Con-Gehäuse: Schritt 1, Bild 1 von 1
    • Entferne die 4 Tri-Wing Schrauben auf der Rückseite des Joy-Con.

    • Dies sind die einzigen Tri-Wing Schrauben auf dem Joy-Con. Alle anderen Schrauben erfordern einen Kreuzschlitzschraubendreher.

  2. Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 2, Bild 1 von 1
    • Klappe die hintere Schale auf, um den Akku freizulegen.

  3. Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 3, Bild 1 von 2 Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 3, Bild 2 von 2
    • Entferne die Schraube, die die Schiene mit der Rückenschale verbindet.

  4. Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 4, Bild 1 von 1
    • Entferne den Akku und trenne ihn von der Hauptplatine ab. Du kannst die Kabel mit einer Pinzette oder mit den Händen von der Hauptplatine abziehen.

    • der Akku lässt sich möglicherweise aufgrund von Klebstoff nur schwer entfernen. Ein Spudger kann helfen, ihn vom Gehäuse zu lösen.

    I messed up the pins for one of the ribbon cables trying to remove the battery connector, be careful with this one, had to order a new motherboard for my joycon

    Milky Manz - Antwort

  5. Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 5, Bild 1 von 2 Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 5, Bild 2 von 2
    • Bevor du den nächsten Schritt durchführst, merke dir den Sitz des Antennenkabels für den korrekten Wiederzusammenbau.

    • Entferne den kleinen Antennenchip (im zweiten Bild) und trenne ihn von der Hauptplatine.

  6. Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 6, Bild 1 von 1
    • Entferne die 3 Schrauben, mit denen das Akkugehäuse im Gehäuse befestigt ist.

  7. Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 7, Bild 1 von 3 Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 7, Bild 2 von 3 Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 7, Bild 3 von 3
    • Entferne die Flachbandkabel, die die Schiene und das Akkugehäuse mit der Hauptplatine verbinden. Entriegle die Kabel, indem du den Steckverbinder mit einem Spudger nach oben klappst, und dann das Kabel aus dem Steckverbinder herausziehst.

    • Du kannst die Schiene auch angeschlossen lassen, es ist dann aber etwas unbequemer.

    • Achte darauf, dass du die Stecker nicht in die falsche Richtung öffnest. Der Stecker nahe bei den Schultertasten muss von der Schiene (dem schwarzen Teil) weg gelöst werden, der Stecker nahe beim Vibrationsmotor in die entgegengesetzte Richtung zur Schiene (dem dünnen grauen Teil) hin.

    Gibt es die Platine für die beiden Taster an der Ladeschiene auch als Ersatzteil? Wenn ich der Joy-Con zusammengebaut ist und damit das Flachbandkabel zusammengedrückt wird funktionieren die beiden Taster nicht. Wenn der Joy-Con auseinander gebaut ist und das Kabel langestreckt ist, dann funktionieren die beiden Taster.

    Ich hoffe, dass es am Kabel liegt und nicht am Kontakt auf dem Motherboard.

    Schulte Kippen - Antwort

    HEY, BE CAREFUL WITH THOSE RIBBON CABLE CLIPS.

    The clip towards the R/ZR buttons releases from the side the cable plugs in.

    The clip towards the rumble motor releases from _the opposite side_ as the cable.

    Mr. Llama - Antwort

    Thank you for this! I was wondering why it wasn’t coming up lol

    pattie -

    Um… what happens if you accidentally push on the gray part of the one near the rumble motor?

    Elise Glover - Antwort

    I found out… it breaks the ability to dock your controller to your switch, you will only be able to play wirelessly and won’t be able to charge your controller. Don’t be like me.

    el15ecg - Antwort

  8. Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 8, Bild 1 von 3 Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 8, Bild 2 von 3 Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 8, Bild 3 von 3
    • Entferne den Vibrationsmotor, indem du den weißen 2-poligen Stecker abziehst.

    WARNING

    do not attempt to remove the connector if it can be avoided- it is held in place by two incredibly thin metal strips that can easily bend and warp, making it impossible to put the connector back into place.

    The Nones - Antwort

  9. Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 9, Bild 1 von 3 Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 9, Bild 2 von 3 Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 9, Bild 3 von 3
    • Entferne den schwarzen ZR-Knopf aus dem Akkugehäuse.

    • Entferne den Knopfsensor, indem du ihn aus dem Akkugehäuse herausschraubst.

  10. Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 10, Bild 1 von 2 Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 10, Bild 2 von 2
    • Entfern die beiden Kreuzschlitzschrauben, mit denen der Joystick an der Hauptplatine befestigt ist.

    • Ziehe das Flachbandkabel des Joysticks von der Hauptplatine ab.

    The joystick ribbon cable releases from the side _opposite_ where the cable plugins in.

    Mr. Llama - Antwort

  11. Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 11, Bild 1 von 2 Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 11, Bild 2 von 2
    • Entferne die beiden Schrauben, die die Hauptplatine mit dem Gehäuse verankern.

    Notable omission: be sure to disconnect the Ribbon cables near the bottom left (directly next to the rumble motor connector). You will have to swap the IR sensor and whatever the gold ribbon cable goes to/is (apologies, I don’t really know). Both are loosely held down with adhesive so just do that when you swap the buttons in the next step. When reconnecting the ribbon cables to the motherboard, I found it MUCH easier to put the ribbon cables back in place before screwing in the motherboard. I am amateur at this (only have fixed a couple iphones and few sets of joycons) but I found the angle to be particularly challenging if the motherboard was screwed in.

    Garrett Catlin - Antwort

    Also omitted: be sure to transfer the NFC antenna. It’s the black rectangle that surrounds the joystick that connects to the motherboard with a light brown cable. It’s lightly held in with adhesive, so a little prying should get it loose.

    Mr. Llama - Antwort

  12. Austausch des rechten Nintendo Switch Joy-Con Gehäuse: Schritt 12, Bild 1 von 1
    • Übertrage alle Knöpfe auf das Ersatzgehäuse.

    • Wenn irgendwelche Silikon-Knopfabdeckungen fehlen, könnten sie noch auf der Rückseite der Hauptplatine kleben.

Abschluss

Um dein Gerät wieder zusammenzubauen, folge diesen Anweisungen in umgekehrter Reihenfolge.

52 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

4 Kommentare

Not quite as thorough as the other Joy-con tear down but always a handy thing to have, going by the pictures it gave me all the information I needed personally concerning the screws, so I was able to strip the whole controller down and swap it into another shell. It is straight forward once you get in to it and have to give the author their much deserved credit for posting this up!

Lee Whittaker - Antwort

Very good detailed guide, only thing I would change is I’d probably take the rumble motor out right after of even before the battery. It’s pretty easy to remove, you can do it at anytime after opening, and it gets the wires out of the way to make other parts easier.

Dominic Garcia - Antwort

I am having difficulty removing the ribbon cable next to the rumble motor on step 7. It would be nice to have a photo of which way the clamp is expected to swing; I suspect I know the correct direction, but my tools are bending it instead.

earthexe - Antwort

In fact, this step is unnecessary unless you are replacing the buttons or rail case. The rail may remain attached if you are only replacing the front, back, and middle casing.

earthexe -

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 43

Letzte 7 Tage: 259

Letzte 30 Tage: 1,241

Insgesamt: 78,783