Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 1
    • 2 Screws on each side

    • 6 Screws on top

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 1
    • Remove Both Fans

    • 2 - Screws each

    • 1 - Pull cable each

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 1
    • Leave some length to solder with and to reach connector on main board.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 1
    • Strip Wires, Tin Wires, and prep by adding heat shrink tubing on wires (before shrinking).

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 3 : Schritt 5, Bild 2 von 3 : Schritt 5, Bild 3 von 3
    • For Both Fans

    • Solder the new fan to the old connector using the following pinout.

    • Adjust heat shrink tubing so it covers the solder joints and use heat gun to shrink tubing.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 1
    • Re-assemble fans to device with fan label facing out.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 1
    • OPTIONAL - Use Small Round Nose Pliers to break off case grill to make fan even quieter.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 1
    • Re-Assemble Case

Ziellinie

4 weitere Nutzer:innen haben diese Anleitung absolviert.

Kevin Krautle

Mitglied seit: 10/10/16

508 Reputation

2 Anleitungen geschrieben

5 Kommentare

I have an ATEM Production Studio 4K which had the same issue. This guide was helpful to know how to map the exhaust fan wiring. There are 2 12v heat sync fans that have the same color scheme. I just crimped the wires strait across, and everything worked. I’m now able to live edit without the distraction of a loud switch!

Thank you!!

longears - Antwort

I just did the same on my atem m/e production 4k but the side fans (exhaust) are not on. I wonder if there’s a threshold at which they power on? Any recommendation? The heat sink fans work right away.

Beto Gudiño -

Can I have a schematic diagram for this product ?

Jay Makwana - Antwort

Awesome video, thanks! Do you have a similar iFixit kit and video for the ATEM Mini Pro?

Al Rodriguez - Antwort

Great mod! Did this on my TV Studio HD, nearly non hearable now :)

Andi M - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 13

Letzte 30 Tage: 71

Insgesamt: 7,098