Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 2 : Schritt 1, Bild 2 von 2
    • Remove the four 19mm Phillips #2 screws from the base of the device.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 3 : Schritt 2, Bild 2 von 3 : Schritt 2, Bild 3 von 3
    • Turn the device over, holding the base on with your thumbs.

    • Hold the device tightly to prevent the base from falling off.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 3 : Schritt 3, Bild 2 von 3 : Schritt 3, Bild 3 von 3
    • Gently lift the top off of the device.

    • Lift in the direction shown to avoid damaging the wires connecting the top and base of the device.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 3 : Schritt 4, Bild 2 von 3 : Schritt 4, Bild 3 von 3
    • Pinch and unplug the white connector from the device.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 3 : Schritt 5, Bild 2 von 3 : Schritt 5, Bild 3 von 3
    • Gently pinch and pull on the white ribbon cable to disconnect it from the base.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 1
    • The base should now be completely detached from the device.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 3 : Schritt 7, Bild 2 von 3 : Schritt 7, Bild 3 von 3
    • Wedge the spudger between the top and front panel on the right side of the device.

    • Push down on the spudger, lifting the front panel away from the top panel until it pops out of the right side.

    • Repeat for the left side of the device.

    • Too much pressure may break the panel, but it should flex slightly before it pops out.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 3 : Schritt 8, Bild 2 von 3 : Schritt 8, Bild 3 von 3
    • Once the panel is released on the left side, wedge the spudger between the top panel and front grill of the device as shown.

    • Apply pressure and move the spudger upward until the front grill pops out.

    • Repeat for the right side of the device.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 1
    • Lift the front grill away from the device.

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 10, Bild 1 von 2 : Schritt 10, Bild 2 von 2
    • Turn the device around.

    • Wedge the spudger into the larger part of the gap under the back of the device.

  11. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 11, Bild 1 von 1
    • Move the spudger up until the button panel is loose.

    • Push forward on the back of the button panel to disconnect the panel from the top of the device.

  12. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 12, Bild 1 von 2 : Schritt 12, Bild 2 von 2
    • Turn the device around.

    • Pull the button panel forward with one hand and push the screen assembly into the device with the other to disconnect the button panel.

  13. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 13, Bild 1 von 3 : Schritt 13, Bild 2 von 3 : Schritt 13, Bild 3 von 3
    • Gently pull the top of the screen assembly away from the device.

  14. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 14, Bild 1 von 2 : Schritt 14, Bild 2 von 2
    • Lift the screen assembly upward and pull the white wire strip out of the device.

Ziellinie

4 weitere Nutzer:innen haben diese Anleitung absolviert.

Cassie Harriman

Mitglied seit: 04/18/17

1.033 Reputation

5 Anleitungen geschrieben

Team

Cal Poly, Team S15-G2, Banghart Spring 2017 Mitglied von Cal Poly, Team S15-G2, Banghart Spring 2017

CPSU-BANGHART-S17S15G2

4 Mitglieder

6 Anleitungen geschrieben

5 Kommentare

Great! This device is the best wave system in sound accurate. All frequencies sounds clear!!! Awesome!!!

srmrs - Antwort

Nicely done.  Love the details.  Just one question - where can I get the replacement screen?

Patsy Hamilton - Antwort

Instructions were PERFECT! Thank you. I found my replacement screen on ebay for $25, took a chance that it would work as stated by the seller. Otherwise I would have thrown the radio away.

John Stine - Antwort

I performed the repair as directed. It was easy especially if you have a plastic spung to work with. Problem comes from the new display once installed shows all the characters? Unplugged it and re-plugged but still stuck in all character test mode?

plhamp - Antwort

How to purchase White wire strip

Bruce Ebneter - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 7

Letzte 7 Tage: 27

Letzte 30 Tage: 167

Insgesamt: 9,906