Einleitung

This guide will walk you through the process of replacing a dead or broken LCD screen on a Brother PT-D200.

Ersatzteile

Kein Ersatzteil erforderlich.

Flip the device over and press down on the indication arrows located at the top center of the back cover and pull it open.
  • Flip the device over and press down on the indication arrows located at the top center of the back cover and pull it open.

Kommentar hinzufügen

Remove the six AAA batteries.
  • Remove the six AAA batteries.

Kommentar hinzufügen

Use the Helping Hand 1/4" screwdriver to unscrew the six 3/16" corner screws.
  • Use the Helping Hand 1/4" screwdriver to unscrew the six 3/16" corner screws.

Kommentar hinzufügen

Close the back cover and then flip the device over and separate the top half from the bottom half as shown.
  • Close the back cover and then flip the device over and separate the top half from the bottom half as shown.

  • Be gentle when lifting the top of the device, there is a ribbon cable attaching the two halves together.

Kommentar hinzufügen

Gently pull out the ribbon cable from the circuit board.
  • Gently pull out the ribbon cable from the circuit board.

  • The ribbon cable is very fragile.

Kommentar hinzufügen

Remove two-pin plastic connector from the circuit board.
  • Remove two-pin plastic connector from the circuit board.

  • Gently pull the two-pin connector from the circuit board to avoid damaging the board.

Kommentar hinzufügen

Remove the two 3/16" screws from the circuit board using the Helping Hand 1/4" screwdriver. Remove the two 3/16" screws from the circuit board using the Helping Hand 1/4" screwdriver.
  • Remove the two 3/16" screws from the circuit board using the Helping Hand 1/4" screwdriver.

Kommentar hinzufügen

Release the two black clips that hold the LCD cable ribbon in place. To release, pull the clips towards the ribbon.
  • Release the two black clips that hold the LCD cable ribbon in place. To release, pull the clips towards the ribbon.

Kommentar hinzufügen

Disconnect the LCD ribbon cable from the circuit board.
  • Disconnect the LCD ribbon cable from the circuit board.

Kommentar hinzufügen

On the top portion of the device there are four grey clips locking the faceplate in place.  The two top clips are circled in the image. The two others are located in the other corners of the device.
  • On the top portion of the device there are four grey clips locking the faceplate in place. The two top clips are circled in the image. The two others are located in the other corners of the device.

Kommentar hinzufügen

Pull the clips inward two at a time, first the top then the bottom, to snap the face plate off. Pull the clips inward two at a time, first the top then the bottom, to snap the face plate off.
  • Pull the clips inward two at a time, first the top then the bottom, to snap the face plate off.

Kommentar hinzufügen

Peel off the rubber keyboard of the device. Peel off the rubber keyboard of the device.
  • Peel off the rubber keyboard of the device.

Kommentar hinzufügen

Lift the LCD screen out of place. Lift the LCD screen out of place.
  • Lift the LCD screen out of place.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Jeston Mitchell

Mitglied seit 24.01.2014

308 Reputation

3 Anleitungen geschrieben

Team

Cal Poly, Team 13-16, Regan Winter 2014 Mitglied von Cal Poly, Team 13-16, Regan Winter 2014

CPSU-REGAN-W14S13G16

4 Mitglieder

9 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 2

Letzte 30 Tage: 17

Insgesamt: 692