Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 1
    • Using a #00 Phillips screw driver, remove three 4.4 mm Phillips screws as indicated by the red circles.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 2 : Schritt 2, Bild 2 von 2
    • Using your finger, peel back the textured grip so the components are separated.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 3 : Schritt 3, Bild 2 von 3 : Schritt 3, Bild 3 von 3
    • Using the flat end of a spudger, loosen the connection between the front panel and the device.

    • Remove the front panel using your hands.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 1
    • Turn Camera over.

    • Using a #00 Phillips screw driver, unscrew the two 4.9 mm Phillips screws located on either side of the viewfinder.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 1
    • Using a #00 Phillips screw driver, unscrew the one 5.7 mm Phillips screw located next to the LCD screen.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 1
    • Lay the camera on its back.

    • Unsolder the flash connection from the motherboard as noted by the blue circle.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 3 : Schritt 7, Bild 2 von 3 : Schritt 7, Bild 3 von 3
    • Remove the top panel by lifting it from the back, pushing it forward over the camera and letting it rotate down in front of the camera.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 1
    • Using a #00 Philllips screw driver, unscrew the 6.8 mm Phillips screw that holds the strap anchor noted by the red circle.

    • Remove the strap anchor.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 1
    • Unlatch the back panel.

    • Using a #00 Phillips screw driver, unscrew the six screws on the bottom of the camera.

    • One 7.4 mm Phillips screw

    • Two 6.0 mm Phillips screws

    • Two 4.4 mm Phillips screws

    • One 3.9 mm Phillips screw

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 10, Bild 1 von 3 : Schritt 10, Bild 2 von 3 : Schritt 10, Bild 3 von 3
    • From the bottom of the camera push the hinge rod in with your finger.

    • Return the camera to its upright position.

    • Use pliers (or tweezers) to pull the rod out from the top.

  11. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 11, Bild 1 von 1
    • Using a 00 Phillips screw driver, unscrew the two 4.9 mm Phillips screws. on the inside of the camera.

  12. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 12, Bild 1 von 1
    • Using a 00 Phillips screw driver, unscrew the two 4.3 mm Phillips screws on the side of the camera.

    • Use your fingers to pull out the plug that is located between the screw holes.

  13. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 13, Bild 1 von 2 : Schritt 13, Bild 2 von 2
    • Use the flat end of a spudger to pop the grip off and remove grip.

  14. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 14, Bild 1 von 2 : Schritt 14, Bild 2 von 2
    • Pry off the small metal brace holding the LCD screen. (Push forward and slide toward the center)

  15. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 15, Bild 1 von 1
    • Lift out the LCD screen.

  16. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 16, Bild 1 von 1
    • Using a 00 Phillips screw driver, unscrew the 7.4 mm Phillips screw on the top of the camera.

    • Using a 00 Phillips screw driver, unscrew the 4.9 mm Phillips screw on the top of the camera.

  17. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 17, Bild 1 von 2 : Schritt 17, Bild 2 von 2
    • Lift the LCD mount to reveal the logic board.

  18. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 18, Bild 1 von 2 : Schritt 18, Bild 2 von 2
    • Using a 00 Phillips screw driver, unscrew the 4.9 mm Phillips screw on the back of the camera.

    • Using a 00 Phillips screw driver, unscrew the 5.8 mm Phillips screw on the top of the camera.

  19. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 19, Bild 1 von 2 : Schritt 19, Bild 2 von 2
    • Use an Exacto knife to cut the white calking on the side of the side panel

    • Pull the side panel away from the camera.

  20. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 20, Bild 1 von 2 : Schritt 20, Bild 2 von 2
    • The large cylindrical object on the right side of the board is the flash capacitor.

    • WARNING: The flash capacitor may carry high voltage, that may persist for hours or even days after the camera has been switched off and/or the battery has been removed.

    • Touching the circuit board while the capacitor still holds its charge may result in a painful electric shock that you will long remember.

    • To make the board safe to work on, short out the two marked terminals with a capacitor discharge tool or the blade of a screwdriver or similar implement (with an insulated handle!) You might have to use moderate pressure to punch through the white goop that covers one of the terminals.

    • There might be little sparks and/or an audible pop. Be careful not to short other solder connections nearby.

    • Use a multimeter to check that dangerous voltage is no longer present before you proceed.

    • Unsolder all of the wires on the top of the logic board.

  21. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 21, Bild 1 von 3 : Schritt 21, Bild 2 von 3 : Schritt 21, Bild 3 von 3
    • Lift up on the board and pull towards the grip.

  22. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 22, Bild 1 von 3 : Schritt 22, Bild 2 von 3 : Schritt 22, Bild 3 von 3
    • Flip the board over.

    • Unsolder the two wires on the bottom of the board.

Ziellinie

Zach

Mitglied seit: 04/04/12

43 Reputation

8 Anleitungen geschrieben

Team

Cal Poly, Team 14-9, Forte Spring 2012 Mitglied von Cal Poly, Team 14-9, Forte Spring 2012

CPSU-FORTE-S12S14G9

5 Mitglieder

36 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 3

Letzte 30 Tage: 15

Insgesamt: 3,032