Zum Hauptinhalt wechseln

Einleitung

This guide involves taking off the entire casing of the camera. It will prepare the user to perform more complicated and problem-specific repairs.

Ersatzteile

Keine Ersatzteile angegeben.

  1. Canon PowerShot A460 Back Casing Replacement, Battery: Schritt 1, Bild 1 von 1
    • Slide the switch on the battery cover labeled "CARD/BATT. OPEN." to the right.

    • While still holding the switch, pull the cover down, allowing it to release and open.

  2. Canon PowerShot A460 Back Casing Replacement: Schritt 2, Bild 1 von 1
    • Tilt the camera slightly to allow the batteries to fall out.

  3. Canon PowerShot A460 Back Casing Replacement: Schritt 3, Bild 1 von 1
    • Press on and release the memory card to eject it.

  4. Canon PowerShot A460 Back Casing Replacement, Front Casing: Schritt 4, Bild 1 von 1
    • Unscrew the 5mm Phillips #00 screw from the bottom of the camera.

    • Make sure to keep the different size screws organized to make reassembling the camera simpler.

  5. Canon PowerShot A460 Back Casing Replacement: Schritt 5, Bild 1 von 1
    • Unscrew the three 2mm Phillips #00 screws that are located on the bottom of the camera.

  6. Canon PowerShot A460 Back Casing Replacement: Schritt 6, Bild 1 von 1
    • Remove the 4mm Phillips #00 screw that is located on the left side of the camera, if the display screen is facing you.

  7. Canon PowerShot A460 Back Casing Replacement: Schritt 7, Bild 1 von 1
    • Take out the 4mm Phillips #00 screw under the rubber flap on the right end of the camera.

  8. Canon PowerShot A460 Back Casing Replacement: Schritt 8, Bild 1 von 2 Canon PowerShot A460 Back Casing Replacement: Schritt 8, Bild 2 von 2
    • Remove the second battery cover on the bottom of camera.

    • Take the silver battery out of the camera.

  9. Canon PowerShot A460 Back Casing Replacement: Schritt 9, Bild 1 von 3 Canon PowerShot A460 Back Casing Replacement: Schritt 9, Bild 2 von 3 Canon PowerShot A460 Back Casing Replacement: Schritt 9, Bild 3 von 3
    • Remove the 4mm Phillips #00 screw on the inside of the flap that hides the battery and memory card slots.

    • Remove the light grey, plastic piece.

    • Remove the plastic portion of the battery flap cover. The metal piece will remain attached.

  10. Canon PowerShot A460 Back Casing Replacement: Schritt 10, Bild 1 von 3 Canon PowerShot A460 Back Casing Replacement: Schritt 10, Bild 2 von 3 Canon PowerShot A460 Back Casing Replacement: Schritt 10, Bild 3 von 3
    • Slightly pull on each side of the camera. It should loosen up and come apart.

    • If it does not pull apart right away, use a little more force.

    • Do not give up!

  11. Canon PowerShot A460 Back Casing Replacement, Back Casing: Schritt 11, Bild 1 von 1
    • Remove the back case of the camera by pulling from the top.

    • Be careful when pulling off the case. There is a delicate gold ribbon connecting the bottom of the camera to the back case.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Team

Cal Poly, Team 19-42, Regan Winter 2013 Mitglied von Cal Poly, Team 19-42, Regan Winter 2013

CPSU-REGAN-W13S19G42

4 Mitglieder

12 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzten 24 Stunden: 1

Letzten 7 Tage: 5

Letzten 30 Tage: 25

Insgesamt: 2,082