Einleitung

First you will remove the batteries and back cover of the camera. You will unscrew the LCD. You will then remove the ribbon attached to the logic board. Finally you will unsolder the LCD from the logic board.

The battery hatch is on the bottom of the camera. CAUTION: Locate the switch to open the hatch and push gently toward the front of the camera. Too much force can break the hatch.
    • The battery hatch is on the bottom of the camera.

    • CAUTION: Locate the switch to open the hatch and push gently toward the front of the camera. Too much force can break the hatch.

    • While the switch is pushed forward, pull the cover away from the camera.

Can the hatch be replaced. The piece that holds the hatch is broken.

alisonbforman46 - Antwort

This camera requires AA batteries. To remove batteries, simply allow them to fall out of the camera.
    • This camera requires AA batteries. To remove batteries, simply allow them to fall out of the camera.

    • The clock battery cover is shown here in the purple circle. Use a fingernail to lift the battery out of the camera.

Kommentar hinzufügen

When replacing the AA batteries, verify they are oriented correctly by following the (+) and (-) signs on the camera.
  • When replacing the AA batteries, verify they are oriented correctly by following the (+) and (-) signs on the camera.

Kommentar hinzufügen

Remove the screw located under the rubber flap on the left side of the camera using a magnetic screwdriver.
  • Remove the screw located under the rubber flap on the left side of the camera using a magnetic screwdriver.

Kommentar hinzufügen

Remove the two screws located on the other side of the camera using a magnetic screwdriver
  • Remove the two screws located on the other side of the camera using a magnetic screwdriver

Kommentar hinzufügen

Remove the three screws located at the bottom of the camera using a magnetic screwdriver.
  • Remove the three screws located at the bottom of the camera using a magnetic screwdriver.

Kommentar hinzufügen

Open the battery cover.
  • Open the battery cover.

  • Using the iPod tool, push up gently around all edges of the camera.

Kommentar hinzufügen

Remove the four (4) screws near the corners of the LCD.
  • Remove the four (4) screws near the corners of the LCD.

Kommentar hinzufügen

CAUTION: The LCD is connected to the logic board with different wires and a ribbon. Using too much force may disconnect these parts.
  • CAUTION: The LCD is connected to the logic board with different wires and a ribbon. Using too much force may disconnect these parts.

  • Lift the screen off of the logic board.

Kommentar hinzufügen

With the LCD pulled back in one hand and using a blue iPod opener tool, pull the black retaining clip up and remove the ribbon.
  • With the LCD pulled back in one hand and using a blue iPod opener tool, pull the black retaining clip up and remove the ribbon.

Kommentar hinzufügen

Use tweezers to unsolder the wires from the bottom left corner on the back of the LCD.
  • Use tweezers to unsolder the wires from the bottom left corner on the back of the LCD.

  • Remove the solder from the wires.

Kommentar hinzufügen

The LCD is now free from the camera and you are now able to replace it with the new screen.
  • The LCD is now free from the camera and you are now able to replace it with the new screen.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Zach

Mitglied seit 11.10.2010

237 Reputation

6 Anleitungen geschrieben

Team

Cal Poly, Team 9-19, Regan Fall 2010 Mitglied von Cal Poly, Team 9-19, Regan Fall 2010

CPSU-REGAN-F10S9G19

4 Mitglieder

7 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 2

Letzte 30 Tage: 5

Insgesamt: 8,764