Zum Hauptinhalt wechseln

Canon PowerShot G16 Motherboard Replacement

Was du brauchst

  1. Canon PowerShot G16 Motherboard Replacement, Battery: Schritt 1, Bild 1 von 3 Canon PowerShot G16 Motherboard Replacement, Battery: Schritt 1, Bild 2 von 3 Canon PowerShot G16 Motherboard Replacement, Battery: Schritt 1, Bild 3 von 3
    • Open the battery flap on the bottom of the camera by applying pressure and pushing in the direction of the arrow.

    • Remove your finger and allow the flap to pop open.

  2. Canon PowerShot G16 Motherboard Replacement: Schritt 2, Bild 1 von 3 Canon PowerShot G16 Motherboard Replacement: Schritt 2, Bild 2 von 3 Canon PowerShot G16 Motherboard Replacement: Schritt 2, Bild 3 von 3
    • Push the brown lever so that it pivots counterclockwise.

    • Grip and remove the battery.

    If I cannot open card/Batt. Open how??

    Jose Ocasio - Antwort

  3. Canon PowerShot G16 Motherboard Replacement, Button Circuit Board: Schritt 3, Bild 1 von 3 Canon PowerShot G16 Motherboard Replacement, Button Circuit Board: Schritt 3, Bild 2 von 3 Canon PowerShot G16 Motherboard Replacement, Button Circuit Board: Schritt 3, Bild 3 von 3
    • Remove the ring around the lens by simultaneously pressing the black button located at the bottom right of the ring and rotating the ring counterclockwise.

  4. Canon PowerShot G16 Motherboard Replacement: Schritt 4, Bild 1 von 1
    • Remove the four 3.3 mm screws on the bottom of the camera using a Phillips #00 screwdriver.

  5. Canon PowerShot G16 Motherboard Replacement: Schritt 5, Bild 1 von 1
    • Remove the 3.3 mm screw on the right side of the viewfinder using a Phillips #00 screwdriver.

  6. Canon PowerShot G16 Motherboard Replacement: Schritt 6, Bild 1 von 1
    • Remove the two 3.3 mm screws near the speaker using a Phillips #00 screwdriver.

  7. Canon PowerShot G16 Motherboard Replacement: Schritt 7, Bild 1 von 1
    • Open the port cover by lifting up the tab with your finger and remove the 3.3 mm screw underneath the cover using a Phillips #00 screwdriver.

    • Remove the other 3.3 mm screw below the ports using a Phillips #00 screwdriver.

    red screw is 7,3 mm

    alepav78 - Antwort

  8. Canon PowerShot G16 Motherboard Replacement: Schritt 8, Bild 1 von 2 Canon PowerShot G16 Motherboard Replacement: Schritt 8, Bild 2 von 2
    • Using your fingers, carefully pull the the back cover off by grabbing the bottom left of the back cover and pulling outwards.

  9. Canon PowerShot G16 Motherboard Replacement: Schritt 9, Bild 1 von 1
    • Using your fingers, carefully pry the front cover off starting at the bottom right.

  10. Canon PowerShot G16 Motherboard Replacement: Schritt 10, Bild 1 von 2 Canon PowerShot G16 Motherboard Replacement: Schritt 10, Bild 2 von 2
    • Remove the 3.8 mm screw at the bottom right of the port cover housing using a Phillips #00 screwdriver.

    • Lift away the port cover housing.

  11. Canon PowerShot G16 Motherboard Replacement: Schritt 11, Bild 1 von 1
    • Reorient the camera so that you are looking at the back.

    • Make sure to pull the connector straight down as pulling up may cause harm to the connector.

    • Unplug the button circuit board from the motherboard by unlocking the ZIF connector (gently lift the brown lock that keeps the cable in place).

    • Pull the connector downwards with the tweezers.

    This is not completely correct. In order to pull the connector down without force, the little grey tap on the top of the connectorbox has to be flipped up.

    This particular step cost me the connection to the button curcuit board. I would be grateful for an indication of where I can buy a replacement. Thanks.

    Martin Salamon - Antwort

    You saved my connection. Thank you. iFixit... I'm somewhat disappointed these steps haven't been corrected.

    It's worth noting that I had no luck with tweezers when attempting to remove the ribbon cable. The correct procedure would be to carefully lift the plastic clip with an iFixit spudger and then continue to step 12. The ribbon cable will pull out gently without any other coercion.

    Phil Howard - Antwort

    The clip is a red/terracotta colour, this should be lifted like a lid (the hinge is mounted in the grey housing). The connector should be pulled downward as described. This should definitely be corrected. Thanks for the comments to assist. I added this for extra clarity on the colours only.

    Jon Mayers - Antwort

  12. Canon PowerShot G16 Motherboard Replacement: Schritt 12, Bild 1 von 1
    • Remove the 3.0 mm screw on the top of the button memory board using a Phillips #00 screwdriver.

    • Remove the 2.8 mm screw on the bottom of the button memory board using a Phillips #00 screwdriver.

  13. Canon PowerShot G16 Motherboard Replacement: Schritt 13, Bild 1 von 1
    • Lift the button circuit board away from the camera.

  14. Canon PowerShot G16 Motherboard Replacement, LCD: Schritt 14, Bild 1 von 3 Canon PowerShot G16 Motherboard Replacement, LCD: Schritt 14, Bild 2 von 3 Canon PowerShot G16 Motherboard Replacement, LCD: Schritt 14, Bild 3 von 3
    • Do not pull the connector upwards as doing so may harm the connector housing.

    • Unlock the ZIF connector for the large connector ribbon by lifting up on the brown flap with the plastic opening tool.

    • Gently pull the connector straight out of the housing with your fingers.

  15. Canon PowerShot G16 Motherboard Replacement: Schritt 15, Bild 1 von 2 Canon PowerShot G16 Motherboard Replacement: Schritt 15, Bild 2 von 2
    • Unplug the small connector ribbon by pulling the cable outwards from the camera using a spudger or your fingers.

    Be careful with this step. I broke the black connector off the motherboard for the small ribbon cable. It is very fragile. You might want to push down on the black connector to hold it in place while gently pulling the ribbon to the right to extract it from the connector. Don’t let the black connect pull up or twist.

    Jeffrey Watkins - Antwort

  16. Canon PowerShot G16 Motherboard Replacement: Schritt 16, Bild 1 von 1
    • Be careful of the copper plate that may fall out once you lift the LCD screen away.

    • Gently lift the LCD away from the camera housing.

  17. Canon PowerShot G16 Motherboard Replacement, Motherboard: Schritt 17, Bild 1 von 2 Canon PowerShot G16 Motherboard Replacement, Motherboard: Schritt 17, Bild 2 von 2
    • Be careful not to bend the EMI shield.

    • Lift and remove the copper EMI shield.

    the screw in the upper right corner disappears magically between the two photos in this step ;) .

    ma.so - Antwort

  18. Canon PowerShot G16 Motherboard Replacement: Schritt 18, Bild 1 von 1
    • Reorient the camera so that you are looking at the front.

    • Remove the 2.8 mm screw right above the screw holding the lens on using a Phillips #00 screwdriver.

    • Remove the 3.3 mm black screw to the left of the front viewfinder using a Phillips #000 screwdriver.

  19. Canon PowerShot G16 Motherboard Replacement: Schritt 19, Bild 1 von 1
    • Reorient the camera so that you are looking at the back.

    • Remove the 6.8 mm screw to the left of the rear viewfinder using a Phillips #00 screwdriver.

    • Remove the 5.2 mm screw to the right of the rear viewfinder using a Phillips #00 screwdriver.

    Somewhere between this step, and Step 21 the screw in the top right (right and up slightly of the orange circled 5.2mm screw) is removed. Suggest doing it here! Same with the one immediately to the right of that.

    Phil Howard - Antwort

    Perfect Comment of Phil Howard! In this moment is necessary remove other screw positioned upper-right

    alepav78 - Antwort

  20. Canon PowerShot G16 Motherboard Replacement: Schritt 20, Bild 1 von 2 Canon PowerShot G16 Motherboard Replacement: Schritt 20, Bild 2 von 2
    • Remove the top 2.3 mm screw from the side with the ports using a Phillips #00 screwdriver.

    • Remove the 4 mm screw right below the one you just removed using a Phillips #00 screwdriver.

    you don’t have to remove the 2.3mm screw in this step, it’s just connected to the top cover

    ma.so - Antwort

  21. Canon PowerShot G16 Motherboard Replacement: Schritt 21, Bild 1 von 2 Canon PowerShot G16 Motherboard Replacement: Schritt 21, Bild 2 von 2
    • Reorient the camera so that you are looking at the back of the camera.

    • Remove the rear viewfinder casing by firmly gripping it and pulling it out bottom first.

    • When reassembling, make sure that the viewfinder is fitted correctly beneath the top cover.

  22. Canon PowerShot G16 Motherboard Replacement: Schritt 22, Bild 1 von 1
    • Remove the newly uncovered 2.8 mm screw from the right of the viewfinder using a Phillips #00 screwdriver.

    • Remove the 4.9 mm screw from top right of the metal casing on the back using a Phillips #00 screwdriver.

    • Remove the 4.3 mm screw from bottom right of the metal casing on the back using a Phillips #00 screwdriver.

    • Remove the newly uncovered screws from the right of the viewfinder using a Phillips #00 screwdriver. (Note, they're already removed on the picture)

    It’s necessary remove olso other little screw positioned on the orange screw ;)

    alepav78 - Antwort

    The right-most screw encircled in green requires a smaller driver than the rest of the screws in this step.

    Brian Sweeney - Antwort

  23. Canon PowerShot G16 Motherboard Replacement: Schritt 23, Bild 1 von 1
    • Remove the 2.7 mm screw from the bottom of the camera using a Phillips #00 screwdriver.

  24. Canon PowerShot G16 Motherboard Replacement: Schritt 24, Bild 1 von 1
    • Reorient the camera so that you are looking at the side with the black felt circle.

    • Use caution around this black felt covered circle that is right below the screw to be removed. This is the speaker and can easily be damaged if pressed too hard or poked with a screwdriver.

    • Remove the 2.8 mm screw from the right side of the camera if you are looking at the front lens using a Phillips #00 screwdriver.

  25. Canon PowerShot G16 Motherboard Replacement: Schritt 25, Bild 1 von 1
    • Reorient the camera so that you are looking at the back of the camera.

    • Remove the metal casing from the back by lifting it away from the camera.

  26. Canon PowerShot G16 Motherboard Replacement: Schritt 26, Bild 1 von 1
    • Disconnect the cable on the top of the motherboard by lifting it up vertically using a plastic opening tool.

  27. Canon PowerShot G16 Motherboard Replacement: Schritt 27, Bild 1 von 2 Canon PowerShot G16 Motherboard Replacement: Schritt 27, Bild 2 von 2
    • Disconnect the cable on the back of the camera to the left of the viewfinder by lifting it up vertically using a plastic opening tool.

  28. Canon PowerShot G16 Motherboard Replacement: Schritt 28, Bild 1 von 2 Canon PowerShot G16 Motherboard Replacement: Schritt 28, Bild 2 von 2
    • Remove the top portion of the casing by firmly grasping it and pulling it upward to lift it off.

    • Some force may be required, but be careful to not bend either side of the top casing up too much or you will damage it.

    At this point the tiny little ribbon cable and flat-flex with two diodes on it (face sensor?) may still be attached to the right of the viewfinder lens. It may just be caught on the two locating pegs. Pull it gently upwards before removing the top.

    Phil Howard - Antwort

    Same precisation of Phil Howard! Please attention at that flat-flex, raise flat before remove machine top!!!!!

    alepav78 - Antwort

  29. Canon PowerShot G16 Motherboard Replacement: Schritt 29, Bild 1 von 3 Canon PowerShot G16 Motherboard Replacement: Schritt 29, Bild 2 von 3 Canon PowerShot G16 Motherboard Replacement: Schritt 29, Bild 3 von 3
    • Open the two ZIF connectors by flipping them up using a plastic opening tool on the motherboard.

    • Make sure to pull the cable ribbon straight out and not up because pulling it up may harm the connector.

    • Be careful not to pinch the cable while pulling it out because it can easily be damaged if pinched. It is helpful to pull it out by the tabs that are built into the connector ribbon.

    • Disconnect the two cable ribbons by pulling them straight out.

  30. Canon PowerShot G16 Motherboard Replacement: Schritt 30, Bild 1 von 2 Canon PowerShot G16 Motherboard Replacement: Schritt 30, Bild 2 von 2
    • Disconnect the lens cable from the motherboard by lifting it up vertically from the motherboard using a plastic opening tool.

    Must remove 2 screw:

    1) bottom-left (little head, long shaft)

    "2) upper-left (big head, short shaft)

    for remove motherboard

    alepav78 - Antwort

  31. Canon PowerShot G16 Motherboard Replacement: Schritt 31, Bild 1 von 2 Canon PowerShot G16 Motherboard Replacement: Schritt 31, Bild 2 von 2
    • Be careful not to pinch the cable while pulling it out because it can easily be damaged. It is helpful to pull it out by the tabs that are built into the connector ribbon.

    • Make sure to pull the cable ribbon straight out and not up because pulling it up may harm the connector.

    • Remove the small cable towards the top by pulling it straight out of its connector using tweezers or your fingers.

    • Remove both Screws on the bottom side of the motherboard

  32. Canon PowerShot G16 Motherboard Replacement: Schritt 32, Bild 1 von 1
    • Lift the motherboard out of the camera.

    It's missing the step to remove two screw that fixes the motherboard

    hugo.marcondes - Antwort

    Probably would be helpful to remove the memory card before doing this step. I’m not sure that was suggested previously.

    Brian Sweeney - Antwort

    Also, just opening the battery compartment door may be helpful in removing the main board.

    Brian Sweeney - Antwort

Abschluss

To reassemble your device, follow these instructions in reverse order.

2 weitere Nutzer:innen haben diese Anleitung absolviert.

Jonathan Harger

Mitglied seit: 01/11/16

1.207 Reputation

5 Anleitungen geschrieben

Team

Cal Poly, Team 70-6, Forte Winter 2016 Mitglied von Cal Poly, Team 70-6, Forte Winter 2016

CPSU-FORTE-W16S70G6

4 Mitglieder

7 Anleitungen geschrieben

2 Kommentare

FYI, new main boards from Canon arrive without firmware installed. I can find no help in how to initialize a new main PCB from Canon. Anyone have links or advise?

Chuck Penrose - Antwort

Hello!

I broke a zif connector at a step 11.

Anybody have a part number for it?

Please help!

egor.shmelev - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 4

Letzte 30 Tage: 15

Insgesamt: 2,149