Einleitung

This shows how to replace the LCD.

Ersatzteile

Kein Ersatzteil erforderlich.

  1. Unscrew five Phillips screws using a #0 Phillips screwdriver.
    • Unscrew five Phillips screws using a #0 Phillips screwdriver.

    • One screw is on upper right corner of the back panel.

    • The other four screws are on the bottom of the camera.

    Kommentar hinzufügen

  2. Open the memory card cover by moving the slide switch toward the top end of of the camera.
    • Open the memory card cover by moving the slide switch toward the top end of of the camera.

    • Remove the memory card from the slot.

    Kommentar hinzufügen

    • Remove the rear cover from the rest of the camera.

    • This may require gentle rocking of the case to free it.

    Kommentar hinzufügen

    • Unscrew the four Phillips screws from the side of the casing and one screw from the bottom using a #0 Phillips screwdriver.

    Kommentar hinzufügen

    • Free the front cover from the rest of the camera.

    • The cover may require gentle rocking to remove.

    Kommentar hinzufügen

    • Unscrew two Phillips screws above the LCD using a #0 Phillips screwdriver.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln!
    Satte 12 € Rabatt auf jeden Einkauf ab 50 €. Einfach den Code FIXMAS12 am Ende deines Bestellvorgangs eingeben
    Frohes Fest, frohes Tüfteln!
    Satte 12 € Rabatt auf jeden Einkauf ab 50 €. Einfach den Code FIXMAS12 am Ende deines Bestellvorgangs eingeben
    • Gently separate the top of LCD from the rest of the camera using your thumb.

    • Be careful not pull the LCD too far because of the ribbon cable connection.

    • Place the Spudger in the hole of the electrical ribbon.

    • Gently pull the ribbon down using the Spudger until it is free from the camera but still connected to the LCD.

    • The LCD will still be connected to the rest of the camera

    Kommentar hinzufügen

    • Unscrew single Phillips screw with a #0 Phillips screwdriver.

    • Free the bottom panel and attached ribbon from the rest of the camera.

    • Be careful not to damage the ribbon.

    Kommentar hinzufügen

    • Turn over the camera.

    • Lift the clear plastic from the face of the camera, peeling the adhesive just below the zoom lens.

    • The plastic will still be connected on the left side.

    Kommentar hinzufügen

    • Place the Spudger between the orange ribbon and the black ribbon gate.

    • Lift the ribbon gate using the Spudger.

    Kommentar hinzufügen

    • Place the Spudger in the corner of the ribbon above the hole.

    • Remove the ribbon from the ribbon gate by pulling the Spudger away from the gate.

    Kommentar hinzufügen

    • Free this ribbon and the bottom panel from the rest of the camera.

    • Be careful not to damage the ribbon.

    Kommentar hinzufügen

    • Turn the camera over so you can see the LCD.

    • Remove single Phillips screw below the LCD using a #0 Phillips screwdriver.

    Kommentar hinzufügen

    • Lift the blue ribbon gate using the Spudger.

    Kommentar hinzufügen

    • Insert the Spudger into the hole of the ribbon.

    • Move the Spudger away from the gate to fully remove ribbon.

    • Be careful not to damage the ribbon.

    Kommentar hinzufügen

    • Lift the LCD away from the rest of the camera.

    Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Nathan Balcom

Mitglied seit 21.01.2010

81 Reputation

8 Anleitungen geschrieben

Team

Cal Poly, Team 16-28, Maness Winter 2010 Mitglied von Cal Poly, Team 16-28, Maness Winter 2010

CPSU-MANESS-W10S16G28

4 Mitglieder

8 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 1

Insgesamt: 2,852