Ersatzteile

Kein Ersatzteil erforderlich.

Remove the two screws from the side panel closest to the camera lens.
  • Remove the two screws from the side panel closest to the camera lens.

  • Note: These screws are 2.9 mm long.

Kommentar hinzufügen

Remove the two screws from the camera bottom panel.
  • Remove the two screws from the camera bottom panel.

  • Note: These screws are 2.9 mm long.

Kommentar hinzufügen

  • Remove the 2 screws from the side panel farthest from the lens.

  • Note: These screws are 2.9 mm long.

Kommentar hinzufügen

  • Pull the back panel away from the camera body, starting at the end with the function buttons.

Kommentar hinzufügen

  • Remove the small cover panel and attached wrist strap mount.

Kommentar hinzufügen

  • Remove the front cover by gently pulling it away from the camera body.

Kommentar hinzufügen

  • Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

Kommentar hinzufügen

  • Remove the 2 screws located at the top of the LCD panel.

  • Note: These screws are 2.4 mm long.

Kommentar hinzufügen

  • Pull up the metal frame surrounding LCD screen starting at the side of the camera.

Kommentar hinzufügen

  • Push the metal frame away from the metal tab using the spudger, to detach the frame.

  • Rotate the metal frame upwards.

  • Note: The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

Kommentar hinzufügen

  • Carefully lift the metal frame from the camera.

  • Remove the black LCD screen, leaving the thin lens pieces in place.

  • Note: BE CAREFUL, both components are attached by an orange connector ribbon and cannot be removed yet!

Kommentar hinzufügen

  • Carefully pull on the orange connector ribbon to disconnect the LCD screen.

  • The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.

  • Note: Tweezers are helpful to disconnect the ribbon

Kommentar hinzufügen

  • Remove the metal frame on the side closest to the flash mechanism. This will expose the screw securing the flash assembly.

Kommentar hinzufügen

  • Remove the screw securing the flash assembly.

  • Note: The screw is 2.4mm long.

Kommentar hinzufügen

  • Use the spudger to carefully disconnect the flash assembly ribbon from the black connector lock.

Kommentar hinzufügen

  • Remove the flash assembly.

  • Note: BE CAREFUL, when handling the flash assembly; touching the capacitor (the black cylinder) could shock you

Kommentar hinzufügen

  • Using the spudger, take off the shutter button by prying the small tab on the front side of the camera.

Kommentar hinzufügen

  • Remove the 2.90mm screw from the lens, near the motherboard.

Kommentar hinzufügen

  • Using the spudger remove the shutter button by prying the small tab on the front side of the camera.

Kommentar hinzufügen

  • With a spudger disconnect the orange connector ribbon as shown.

  • Disconnect the orange connector ribbon that is located under the now removed shutter button.

Kommentar hinzufügen

  • Remove the two 2.90 mm screws from the motherboard.

Kommentar hinzufügen

  • With Tweezers detach the bottom orange ribbon.

Kommentar hinzufügen

  • Remove the screws shown. Start with the outside 6 (3-2.90mm & 3-2.40mm) screws on the metal frame. Then remove the 6 (2.40mm) screws on the back of the lens piece

Kommentar hinzufügen

  • With spudger gently remove the Viewfinder Window that is directly above the lens.

Remove screw attaching viewfinder piece to lens framing.

Adam Biesok - Antwort

  • Detach the mother board with lens from body of camera.

  • Carefully remove the lens from the motherboard. Use tweezers to remove any of the 4 connecting ribbons from the lens.

  • Your lens has been removed from the motherboard and bottom framing.

Kommentar hinzufügen

  • The motherboard (left) is now separated from the lens.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein weiterer Nutzer hat diese Anleitung absolviert.

Phillip Phung

Mitglied seit 19.01.2012

486 Reputation

9 Anleitungen geschrieben

Team

Cal Poly, Team 8-18, Maness Winter 2012 Mitglied von Cal Poly, Team 8-18, Maness Winter 2012

CPSU-MANESS-W12S8G18

4 Mitglieder

10 Anleitungen geschrieben

Which part is the CCD sensor?

yakksoho - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 3

Letzte 7 Tage: 7

Letzte 30 Tage: 38

Insgesamt: 4,866