Canon PowerShot SD500 Digital ELPH LCD Replacement

Diese Anleitung enthält neuere Änderungen. Wechsel zur neuesten unüberprüften Version.

Einleitung

Many companies sell only LCD screens, not complete screen assemblies. When replacing your broken LCD screen, it may be necessary to tear down the screen even further.

Was du brauchst

Schritt 1 Battery

Canon PowerShot SD500 Digital ELPH LCD Replacement, Battery: Schritt 1, Bild 1 von 1

Slide open the battery cover.
Push the small orange tab to the side so the battery can be removed.

Übersetzen

Schritt 2

Slide the battery out of the battery compartment.

Übersetzen

Schritt 3 Front and Rear Casing

Canon PowerShot SD500 Digital ELPH LCD Replacement, Front and Rear Casing: Schritt 3, Bild 1 von 2

Canon PowerShot SD500 Digital ELPH LCD Replacement, Front and Rear Casing: Schritt 3, Bild 2 von 2

Two Phillips screws need to be removed using a #00 Phillips screwdriver. The upper screw is under the USB port cover, which can simply be pulled away gently from the casing. the lower screw is visible on the panel.
The screws are different sizes. The .125 inch screw is located under the USB port cover. The 0.85 inch screw goes in the lower hole on the panel.
When looking at the back of the camera, these two screws are on the right panel of the camera.

Übersetzen

Schritt 4

Remove the right side cover from the camera casing.

Übersetzen

Schritt 5

Remove a .07 inch Phillips screw using a #00 Phillips screwdriver.

Übersetzen

Schritt 6

Remove two .085 inch Phillips screws from the left side of the camera using a #00 Philips screwdriver.

Übersetzen

Schritt 7

Remove the left side cover from the camera.

Übersetzen

Schritt 8

Remove three .15 inch Phillips screws from the bottom of the camera using a #00 Phillips screwdriver.

Übersetzen

Schritt 9

Once the casing is unscrewed, hold the camera with one side facing down, and lift the opposite face of the casing to open it.
Remove the internal camera components and layout out all pieces on a clean surface.
The front and back cover may require gentle rocking to remove.

Übersetzen

Schritt 10 Button Contact Panel

Canon PowerShot SD500 Digital ELPH LCD Replacement, Button Contact Panel: Schritt 10, Bild 1 von 1

Carefully wedge the pry tool under the ribbon in the ribbon gate.
Gently remove the ribbon from the ribbon gate by pulling it away from the gate with the pry tool.
Be careful not to damage the ribbon.

Übersetzen

Schritt 11

Gently press the ribbon back to get access to a Phillips screw behind it.
Be careful not to damage the ribbon.
Unscrew two .125 inch long Phillips screws using a #00 Philips screwdriver.

Übersetzen

Schritt 12

Canon PowerShot SD500 Digital ELPH LCD Replacement: Schritt 12, Bild 3 von 3

Remove the ribbon with a pry tool by gently pulling it out of the ribbon gate tab.
Be careful not to damage the ribbon.
Pull the button board away from the rest of the camera.

Übersetzen

Schritt 13 LCD

Canon PowerShot SD500 Digital ELPH LCD Replacement, LCD: Schritt 13, Bild 1 von 1

Unscrew one .113 inch Phillips screw using a #00 Phillips screwdriver.

Übersetzen

Schritt 14

Lift the LCD screen up and away from the tab that holds it in place on the face of the camera.
Be careful, the LCD screen is still connect to the camera by a ribbon cable.

Übersetzen

Schritt 15

Gently press the pry tool under the ribbon gate and lift up to free the ribbon connecting the LCD to the circuit board.
Be careful not to damage the ribbon.
The LCD can now be completely removed from the camera.