Ersatzteile

Kein Ersatzteil erforderlich.

Using your thumb, slide down and remove the battery cover.
  • Using your thumb, slide down and remove the battery cover.

Kommentar hinzufügen

Using your index finger, remove the old AA battery.
  • Using your index finger, remove the old AA battery.

  • Install the new AA battery.

Kommentar hinzufügen

Slide down the eject button.
  • Slide down the eject button.

  • Pull out the old SmartMedia Card.

  • Insert the new SmartMedia Card.

    • The notched corner of the SmartMedia card should go in the top left corner.

Kommentar hinzufügen

Using a Phillips #00 Screwdriver, remove the two 7.5 mm screws located on the left and right side of the back cover, respectively.
  • Using a Phillips #00 Screwdriver, remove the two 7.5 mm screws located on the left and right side of the back cover, respectively.

Kommentar hinzufügen

Remove the back cover of the Nomad II.
  • Remove the back cover of the Nomad II.

  • Remove the following items located on the left and right side of the device:

    • The rubber USB port cover

    • The plastic lock/unlock switch cover

    • The buttons located on the left side of the device

Kommentar hinzufügen

Using a Phillips #00 Screwdriver, remove the two 5.5 mm screws located in the bottom corners of the battery compartment.
  • Using a Phillips #00 Screwdriver, remove the two 5.5 mm screws located in the bottom corners of the battery compartment.

Kommentar hinzufügen

Using your fingers, carefully remove the battery compartment.
  • Using your fingers, carefully remove the battery compartment.

Kommentar hinzufügen

Using a Phillips #00 Screwdriver, remove the two 5.5 mm screws located on the left and right edges of the circuit board.
  • Using a Phillips #00 Screwdriver, remove the two 5.5 mm screws located on the left and right edges of the circuit board.

Kommentar hinzufügen

Using a pair of tweezers, carefully remove the metal loop attached to the circuit board from its plastic case on the left side of the battery compartment.
  • Using a pair of tweezers, carefully remove the metal loop attached to the circuit board from its plastic case on the left side of the battery compartment.

Kommentar hinzufügen

Pull out the circuit boards.
  • Pull out the circuit boards.

    • When reinserting the circuit boards, press the front face of the boards into the device case until you hear a click.

Kommentar hinzufügen

Position the circuit boards with the USB port facing up.
  • Position the circuit boards with the USB port facing up.

  • Gently separate the circuit boards.

Kommentar hinzufügen

Using a pair of tweezers, gently lift and peel back the thin copper film covering the headphone jack.
  • Using a pair of tweezers, gently lift and peel back the thin copper film covering the headphone jack.

    • Only peel back the film enough to expose the headphone jack.

    • Completely removing the copper film can damage the device.

Kommentar hinzufügen

Gently remove the black adhesive tape from the underside of the headphone jack.
  • Gently remove the black adhesive tape from the underside of the headphone jack.

Kommentar hinzufügen

Desolder the four solder joints securing the headphone jack.
  • Desolder the four solder joints securing the headphone jack.

  • Remove the old headphone jack.

  • Install the new headphone jack.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Craig Fischer

Mitglied seit 24.01.2012

21 Reputation

2 Anleitungen geschrieben

Team

Cal Poly, Team 9-2, Regan Winter 2012 Mitglied von Cal Poly, Team 9-2, Regan Winter 2012

CPSU-REGAN-W12S9G2

5 Mitglieder

5 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 1

Insgesamt: 1,410