Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 2 : Schritt 1, Bild 2 von 2
    • Pop off the top plastic on the device with a flat tool like a flathead screwdriver.

    • Unscrew and remove the two exposed Phillips head screws.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 2 : Schritt 2, Bild 2 von 2
    • Work your way around the recess of the device with a flat tool like a flathead screwdriver.

    • Don't try attempt to open it from the recess between the buttons and the device.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 3 : Schritt 3, Bild 2 von 3 : Schritt 3, Bild 3 von 3
    • Disconnect the wire from the bottom device.

    • Handle with care as the wires tend to disconnect easily.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 1
    • In the top right corner, pull the black foam square off to separate the hard drive from the screen.

    • Handle with care as the hard drive also comes off easily.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 1
    • Unscrew the seven screws placed around the mother board.

    • You will need a one millimeter Phillips head screwdriver.

    • The screws are small, so keep them safely.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 3 : Schritt 6, Bild 2 von 3 : Schritt 6, Bild 3 von 3
    • Flip your device upside down so that the motherboard will loosen.

    • Detach the connector from the motherboard.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 2 : Schritt 7, Bild 2 von 2
    • Tilt the screen diagonally. Separate the screen and motherboard from the device frame.

    • Lift the light gray flap to detach the screen from the motherboard.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 2 : Schritt 8, Bild 2 von 2
    • Separate the clear screen frame from the digital display.

Ziellinie

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

Kirstie G

Mitglied seit: 10/12/16

470 Reputation

4 Anleitungen geschrieben

Team

Texas Tech, Team 12-1, Bennett Fall 2016 Mitglied von Texas Tech, Team 12-1, Bennett Fall 2016

TTU-BENNETT-F16S12G1

4 Mitglieder

4 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 9

Letzte 30 Tage: 34

Insgesamt: 1,219