Zum Hauptinhalt wechseln

DJI Mavic Pro oberes Gehäuse austauschen

Was du brauchst

  1. DJI Mavic Pro oberes Gehäuse austauschen, Akku: Schritt 1, Bild 1 von 3 DJI Mavic Pro oberes Gehäuse austauschen, Akku: Schritt 1, Bild 2 von 3 DJI Mavic Pro oberes Gehäuse austauschen, Akku: Schritt 1, Bild 3 von 3
    • Greife den Akku von beiden Seiten.

    • Drücke die beiden Halteklammern des Akkus.

    • Hebe den Akku nun heraus.

  2. DJI Mavic Pro oberes Gehäuse austauschen, Oberes Gehäuse: Schritt 2, Bild 1 von 1
    • Entferne die sechs 1,5mm Inbus Schrauben.

  3. DJI Mavic Pro oberes Gehäuse austauschen: Schritt 3, Bild 1 von 1
    • Drehe die Drohne nun um, so dass das Gimbal nach oben zeigt.

    • Entferne die beiden 4 mm langen 1,5 mm Inbusbusschrauben nahe am Gimbal-Gehäuse.

    • Entferne die beiden 5 mm langen 1,5 mm Inbusbusschrauben nahe am Gimbal-Gehäuse.

    the author forgot to mention to remove also the two screws right next to the gimbal. in this picture, they are already removed. without removing these, you cannot open the drone!!

    Joris Ott - Antwort

    also, the screws above in the red circles are not the same as the ones in step 2 and 5! They are shorter! I don’t know how long but not 5mm!

    Joris Ott - Antwort

    Yes, please add those screws - almost broke the top case ;-(

    xyz40 - Antwort

    Screws thinner too.

    Lee Day - Antwort

  4. DJI Mavic Pro oberes Gehäuse austauschen: Schritt 4, Bild 1 von 1
    • Entferne die beiden kleinen Abdeckungen mit einer Pinzette.

    BEWARE! The two screws under the covers are not mentioned in step four to be removed, but they show that they have been removed in step five.

    Patrick Madden - Antwort

    Step five should read- Remove the SIX 5mm 1.5 Hex screws that are under the panel pieces by turning the screwdriver counterclockwise.

    Patrick Madden - Antwort

  5. DJI Mavic Pro oberes Gehäuse austauschen: Schritt 5, Bild 1 von 1
    • Entferne die sechs 1,5mm Inbus Schrauben, die sich unter den Abdeckungen befinden.

    You need to remove the 2 screws (as the picture shows) that are adjacent to each side of the gimbal (below the screws circled in the picture. This also connect to the top shell and could cause an issue!

    ellfa1 - Antwort

    What he said!! ^^^

    shaun.cunningham - Antwort

    You might notice that there are two crosshead screws with larger heads (top two circled in image). You do NOT need to touch these as they are not part of the gimbal assembly.

    james.collins1905 - Antwort

    Agree with @elfa1 - do not remove the top two screws, or you will put unnecessary strain on the plastic while moving arms. No need for that at all.

    demanufacturer - Antwort

  6. DJI Mavic Pro oberes Gehäuse austauschen: Schritt 6, Bild 1 von 1
    • Drehe die Drohne nun wieder um.

    • Nutze nun einen Plastiköffner um die Oberseite von der Unterseite zu trennen.

    • Sei Vorsichtig beim Lösen, um eine Beschädigung der Plastiknasen zu vermeiden.

    using pry tool is not necessary - once all top shell screws are removed you should be able to take the top shell off with your hand.

    KopaZ Maymay - Antwort

    Sorry “KopaZ Maymay”, aber der Plastiköffner ist “sowas von erforderlich”, weil man sonst leider die beiden Plastiknasen in der Front riskiert.

    Orbiter - Antwort

    Zudem fehlt hier die Angabe der genauen Lage von beiden vorderen Nasen:

    Sie befinden sich von der Mitte aus gemessen jeweils 9mm nach links und rechts. Der obere Gehäuseteil wird von zwei 5mm breiten Bügeln gehalten, die unter die horizontal nach innen zeigenden Nasen vom unteren Gehäuseteil greifen.

    Orbiter - Antwort

    Sorry “KopaZ Maymay”, but the plastic opener is “so necessary” because otherwise you unfortunately risk the two plastic noses in the front.

    In addition, the exact position of both front noses is missing in the description:

    They are measured 9mm from the center to the left and right. The upper part of the housing is held by two 5mm wide brackets that grip under the noses pointing horizontally inwards from the lower part of the housing.

    Orbiter - Antwort

    Hi, is it a simple replacement. Ie you do not have to reprogram? Thanks

    farkin joker - Antwort

  7. DJI Mavic Pro oberes Gehäuse austauschen: Schritt 7, Bild 1 von 1
    • Fasse den Stecker am Ende des Controllers ganz unten und ziehe ihn vorsichtig heraus.

    Hello there, can anyone tell me, please, what type of connector is this? I ruined mine and i like to fixit.

    Ene Alexandru - Antwort

Abschluss

Um dein Gerät wieder zusammen zu setzen, befolge die Anleitung in umgekehrter Reihenfolge.

6 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Team

Cal Poly, Team S17-G3, White Fall 2018 Mitglied von Cal Poly, Team S17-G3, White Fall 2018

CPSU-WHITE-F18S17G3

4 Mitglieder

14 Anleitungen geschrieben

2 Kommentare

Well done, good instructions - are the two screws under the tabs shorter than the others from the shell?

Lazaro Hernandez - Antwort

Awesome descriptions were perfect except for saying there is 4 acres to be removed under the tabs behind the gimbal. Theirs only 2

shaun.cunningham - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 15

Letzte 30 Tage: 54

Insgesamt: 5,140