Zum Hauptinhalt wechseln

Das Gehäuse der Logitech M170 öffnen

Was du brauchst

  1. Das Gehäuse der Logitech M170 öffnen, Batteriefachabdeckung entfernen: Schritt 1, Bild 1 von 1
    • Schalte die Maus aus und entferne die Batteriefachabdeckung. Von dort aus kannst Du alle Clips erreichen.

  2. Das Gehäuse der Logitech M170 öffnen, Batterie und Aufkleber entfernen: Schritt 2, Bild 1 von 1
    • Entferne die Batterie und den Aufkleber. Es gibt insgesamt 3 Clips die gelöst werden müssen. Zwei sind an den Seiten. Der Dritte befindet sich um Batteriefach unter dem Aufkleber. Logitech versteckt gewöhnlich Befestigungspunkte an ähnlichen Bereichen in anderen kabellosen Mäusen.

    • Es könnte sein, dass Du eine Pinzette benötigst um den Aufkleber leichter zu entfernen.

    • Im nächsten Schritt werden wir die Clips lösen.

  3. Das Gehäuse der Logitech M170 öffnen, Clips lösen: Schritt 3, Bild 1 von 3 Das Gehäuse der Logitech M170 öffnen, Clips lösen: Schritt 3, Bild 2 von 3 Das Gehäuse der Logitech M170 öffnen, Clips lösen: Schritt 3, Bild 3 von 3
    • Finde die Clips. Das Plastikteil des oberen Gehäuses hat eine andere Einfärbung als das untere Gehäuseteil. Du kannst die Clips also an ihrer anderen Einfärbung finden (sollte die gleiche Farbe sein, wie der obere teil des Gehäuses. Hier sind sie schwarz).

    • Wenn du die Clips gefunden hast, ziehe sie nach Aussen/von der Mitte weg (siehe Bild) um sie zu lösen.

    • Du kannst ein kleines Werkzeug benutzen, aber der Kunststoff könnte weich sein. Sei also vorsichtig um die Clips nicht zu beschädigen.

    I cantt, it wont open

    Mr Johns - Antwort

    Mine doesnt have clips.

    brooklyn - Antwort

    very tricky , struggling here

    John Fleming - Antwort

    With the two side clips, it’s not the T-shaped outer bits that need to be pressed, it’s the thicker part lower down. It takes a bit of force to move the clips, but of course care is required.

    Mike Van Emmerik - Antwort

    Thank you. I was struggling with the T shaped parts.

    Efe Muratal -

    best tip: use a screw driver to uncover the bottom clip first. then use your nail to hold it in place(the bottom lid).

    Then use your screw driver (for side clips) to push both the t shaped outer bits with the grey colored bits away from the center.{use the screw driver as a leverage against the outer covering}

    then bada bing bada boom its open

    fawoto7831@fanneat.com - Antwort

  4. Das Gehäuse der Logitech M170 öffnen, Oberteil lösen: Schritt 4, Bild 1 von 3 Das Gehäuse der Logitech M170 öffnen, Oberteil lösen: Schritt 4, Bild 2 von 3 Das Gehäuse der Logitech M170 öffnen, Oberteil lösen: Schritt 4, Bild 3 von 3
    • Wenn Du die 3 Clips gelöst hast, kannst Du Oberteil einfach abziehen. Du kannst etwas nachhelfen indem Du an den Clips schiebst.

    • Wenn sich die hintere Seite gelöst hat, schiebe das ganze Oberteil etwas nach vorne. (Dort sind zwei weitere Haken an der Vorderseite der Maus, wo die Tasten sind, die Verhindern, dass die tasten nach oben gezogen werden). Das sollte dich nun das ganze Oberteil entfernen lassen.

  5. Das Gehäuse der Logitech M170 öffnen, Viel Spaß im Innenleben: Schritt 5, Bild 1 von 3 Das Gehäuse der Logitech M170 öffnen, Viel Spaß im Innenleben: Schritt 5, Bild 2 von 3 Das Gehäuse der Logitech M170 öffnen, Viel Spaß im Innenleben: Schritt 5, Bild 3 von 3
    • Jetzt solltest Du deine Reparaturen im Innenleben durchführen können.

    • Interessant: Logitech hat bei hochpreisigen Modellen hochwertigen Omron-Schalter verbaut. Obwohl das hier nur eine 10-€-Maus ist wurden Mikroschalter von Himake verbaut. Der Widerstand fühlt sich höher an als bei Omron Schaltern. Die Haltbarkeit muss noch getestet werden. Ich habe die Maus nicht so lange, dass ich darüber etwas sagen könnte.

    • Mir gefällt der schraubenlose Design und wie das ohne Kleber gelöst wurde. Es ist wirklich einfach wieder zusammen zu bauen und es gibt weniger Teile die man verlieren könnte oder auf die man achten müsste.

  6. Das Gehäuse der Logitech M170 öffnen, Zusammenbau: Schritt 6, Bild 1 von 2 Das Gehäuse der Logitech M170 öffnen, Zusammenbau: Schritt 6, Bild 2 von 2
    • Um das Oberteil wieder aufzusetzen, zuerst die Haken an der Vorderseite wieder einsetzen bevor die Clips an der Hinterseite einschnappen.

    • Drücke das Gehäuse mit der Handfläche leicht nach unten um die Clips wieder an Ihren Platz schnappen zu lassen.

    • Natürlich musst Du nun die Batterie wieder einsetzen und die Batteriefachabdeckung wieder aufsetzen. Den Kleber im Batteriefach habe ich auch wieder eingesetzt, allerdings etwas höher, damit ich leichter an den Clip komme. Ich war mir nicht sicher ob ich das später noch mal brauchen würde.

    Front, as in towards the wheel end.

    Mike Van Emmerik - Antwort

Ziellinie

90 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

BenZ78 hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

John

Mitglied seit: 08/21/15

2.128 Reputation

1 Anleitung geschrieben

31 Kommentare

My mouse wheel is loose so I cannot scroll using my mouse is there a way that one can tighten it since I've opened it n the mouse wheel just came out.

Vee - Antwort

The same happened to mine, so I used a little bit of super bonder to attached again the wheel to the spinning sensor. Problem solved.

marcosfa -

Thanks man! Your instructions were very useful. Without them, I don't think I would succeeded in fixing my mouse. The optics sensor was just out of place. My mouse is working perfectly now. Thanks again.

samuel.ibrahim - Antwort

Same! They probably came out from falling on the floor, but putting the loose light back on to the transparent thingy thing definitely did the trick.

Jacqueline Fernandes -

the clips on the side arent clipping out

wael al hajj - Antwort

Same issue for me too

Chuah Chee Song -

can someone tell me where the usb receiver is?

Yunus Lawi - Antwort

Thanks for demystifying how to open! There is no power getting to the board but I can 't see any break from the terminal to the board so guess I can"t fix it.

suzan - Antwort

Thanks! Releasing the clips wasn’t easy, but it worked in the end. (I have a M171.) Unfortunately, I couldn’t find anything abnormal while ‘enjoying the insides’, so I didn’t manage to fix it. Do you have any suggestion what I should look at, or what broken parts could be fixed? I guess the mouse just fell on the floor too often, and something is irreparably broken.

Els - Antwort

Thanks ! After release the clips, I found that an internal component was out of place. Now, the mouse works perfect !

Manuel Espejo - Antwort

add close view of shape of clip/snap on so that user knows which side to press for unlocking three latches.

Muhammad Rizwan Sheikh - Antwort

I have an M170 mouse, but aside from the underside look, mine has NO “3 clips” anywhere. And the top does not come off. I put the battery in and no sign of light so must be something wrong. There are no visible “clips”.

GARY MATTHEWS - Antwort

Hi, Before I try opening my M325(hopefully it has similar clips) I want to ask if the issue I am facing is a hardware issue, My mouse registers a double click when I actually do a single click. It is very frustrating as sometime when I try to close an overlapping window , it closes some other application behind it :( . I have tried changing the double click speed setting in the control panel mouse options but no luck.

Srirang Netake - Antwort

for some reason the wheel button stopped working, i opened, cleaned it a bit (it had like 4 years of dust, crumbles and hairs) and magically it started working again (not perfectly, but good enough to avoid spending money on a new one or bother soldering stuff)

Mauro Santopietro - Antwort

Man i atach hooks last but its still working perfectly

SRDS 7 - Antwort

Thanks! I cleaned the wheel and it’s working now.

Salome Khaindrava - Antwort

I was able to open my M170 with instructions from this page. Very helpful. I was trying to see if I could fix the problem with my mouse: When I scroll using the wheel, the page would quickly jump up when I meant to scroll down. I was not able to fix it. Any help? The left-click, right-click and center clicks are fine, but the scroll wheel is something else. When I scroll, the page tends to jump up and down first before following my scroll. Any help is greatly appreciated. Thanks!

Chris Malinao - Antwort

is there a way to reset the mouse?

Mohammed Zameil - Antwort

Why do you need to reset it?

Daniele Carminati -

just pull off battery. To be sure, with something metallic connect both + and - terminals on the battery compartiment for a 5 secs while mouse switch is in ON position.

—-why do you need it?

adolfo Zameza -

My mouse works fine for 10-15 minutes. then stops working abruptly. It works again a few hours or a day later for 10-15 minutes, and then again stops. I didn’t see anything abnormal on the inside. Any tips?

Anonymous - Antwort

Maybe some faulty capacitors?

Daniele Carminati -

John muchas gracias, necesitaba limpiar este mouse para que funcionara de nuevo como nuevo.

Ya estaba enfadado de la falta de precision, una limpieza con cepillo y alcohol isopropilico resolvio todo.

adolfo Zameza - Antwort

Thanks man, this was a gem

Rohit Mukherjee - Antwort

Hi My M170 works well initially but after some time a message pops up on the screen and says that the USB drive you just inserted is malfunctioned.

Trouble shooting done so far - Driver update in the laptop, firm ware of laptop updated not able to update the firm ware of mouse as the tool does not recognize it.

Please help.

mankuagrawal - Antwort

thanks for this. the scroll wheel has gotten loose on my mouse, and i used this tutorial to diagnose the problem. fixed now! if youre havinig trouble loosening the clips, try wedging a small, flat tool under the side clips and turning until it pops up. it needs more force than you think you should use. the bottom clip pops out a lot easier if you do the side ones first.

goblincxnt - Antwort

Bonjour, ma souris M170 ne comporte aucun clip Comment donc ouvrir la souris ? Merci

Anwer RAHAL - Antwort

Thanks for sharing this! Needed to open it to clean the battery coil due to a battery leakage. All set!

Danilo Mazzolani - Antwort

Dear author, thanks for the hints. This article helped me to figure out how to tear down my Logi M190 mouse and the trickiest step was to remove the sticker inside the battery slot and remove the tiny screw.

Amstel Coder - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 36

Letzte 7 Tage: 218

Letzte 30 Tage: 951

Insgesamt: 84,542