Zum Hauptinhalt wechseln

Diese Version enthält möglicherweise inkorrekte Änderungen. Wechsle zur letzten geprüften Version.

Was du brauchst

  1. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 1, Bild 1 von 1
    • Remove the screws that secure the hard-drive assembly to the computer base.

  2. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 2, Bild 1 von 1
    • Open the latch and disconnect the hard-drive cable from the system board.

  3. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 3, Bild 1 von 1
    • Lift the hard-drive assembly off the computer base.

  4. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 4, Bild 1 von 1
    • Remove the screws that secure the hard-drive bracket to the hard drive.

  5. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 5, Bild 1 von 1
    • Lift the hard-drive bracket off the hard drive.

  6. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 6, Bild 1 von 1
    • Disconnect the interposer from the hard drive.

  7. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 7, Bild 1 von 1
    • Connect the interposer to the NEW hard drive.

  8. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 8, Bild 1 von 1
    • Align the screw holes on the hard-drive bracket with the screw holes on the hard drive.

  9. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 9, Bild 1 von 1
    • Replace the screws that secure the hard-drive bracket to the hard drive.

  10. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 10, Bild 1 von 1
    • Align the screw holes on the hard-drive assembly with the screw holes on the computer base.

  11. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 11, Bild 1 von 1
    • Replace the screws that secure the hard-drive assembly to the computer base.

  12. Dieser Schritt ist noch nicht übersetzt. Hilf mit, ihn zu übersetzen!

    : Schritt 12, Bild 1 von 1
    • Slide the hard-drive cable into the system board and close the latch to secure the cable.

Ziellinie

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

darrius

Mitglied seit: 03/26/18

5.213 Reputation

30 Anleitungen geschrieben

Team

RampUP America, Inc. Mitglied von RampUP America, Inc.

Community

42 Mitglieder

1.985 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 4

Letzte 30 Tage: 6

Insgesamt: 148