Zum Hauptinhalt wechseln

Diese Anleitung enthält neuere Änderungen. Wechsel zur neuesten unüberprüften Version.

Dell Latitude X300 Cooling Fan Replacement

Was du brauchst

  1. Dell Latitude X300 Cooling Fan Replacement, Battery: Schritt 1, Bild 1 von 1
    • Before removing the battery from the laptop, make sure the power is off.

    • Push both battery locking clips outward at the same time.

  2. Dell Latitude X300 Cooling Fan Replacement: Schritt 2, Bild 1 von 1
    • Slide the battery out of the laptop.

  3. Dell Latitude X300 Cooling Fan Replacement, Keyboard: Schritt 3, Bild 1 von 1
    • Remove the four 4 mm Phillips #0 screws from the bottom of the laptop.

  4. Dell Latitude X300 Cooling Fan Replacement: Schritt 4, Bild 1 von 2 Dell Latitude X300 Cooling Fan Replacement: Schritt 4, Bild 2 von 2
    • Carefully turn the laptop over and open the screen all the way.

    • Locate the slot to remove the keyboard in the lower left hand corner.

    • Using a spudger as a lever, insert it into the slot and gently pry up.

  5. Dell Latitude X300 Cooling Fan Replacement: Schritt 5, Bild 1 von 1
    • After the keyboard pops up, pull it away from the screen just enough to release the tabs.

    • Don’t pull the keyboard out forcefully as there is still a ribbon attached to the laptop.

  6. Dell Latitude X300 Cooling Fan Replacement: Schritt 6, Bild 1 von 1
    • Unlock the ZIF connector on the computer by pushing the two outside tabs toward the screen.

  7. Dell Latitude X300 Cooling Fan Replacement: Schritt 7, Bild 1 von 1
    • Remove the flexible ribbon from the ZIF connector.

    • Do not pull on the ribbon to remove it from the ZIF connector.

  8. Dell Latitude X300 Cooling Fan Replacement, Palm Rest/Track Pad: Schritt 8, Bild 1 von 1
    • Position the laptop so that the bottom is facing upward.

    • Remove the three 4 mm Phillips #0 screws holding the bottom of the palm rest.

  9. Dell Latitude X300 Cooling Fan Replacement: Schritt 9, Bild 1 von 1
    • Return the laptop to proper position and open the screen.

    • Remove the six 4 mm Phillips #0 screws holding in the palm rest.

  10. Dell Latitude X300 Cooling Fan Replacement: Schritt 10, Bild 1 von 1
    • Gently lift the palm rest and rotate it outward so that the bottom is now facing up.

    • The ribbon attached to the track is short and extremely delicate. Use care when moving the palm rest.

  11. Dell Latitude X300 Cooling Fan Replacement: Schritt 11, Bild 1 von 1
    • Lift up on the small ZIF connector and remove the ribbon.

    • If the ribbon seems stuck, gently wiggle it to remove. Do not pull the ribbon with great force.

  12. Dell Latitude X300 Cooling Fan Replacement, Cooling Fan: Schritt 12, Bild 1 von 1
    • Remove the 4 3 mm screws that hold the cooling fan to the system board.

  13. Dell Latitude X300 Cooling Fan Replacement: Schritt 13, Bild 1 von 1
    • Remove the tape holding the cooling fan wires down.

  14. Dell Latitude X300 Cooling Fan Replacement: Schritt 14, Bild 1 von 1
    • Unplug the cooling fan wires from the system board by gently pulling on the hard molded plastic portion.

    • Be careful not to damage the wires by tugging on them.

  15. Dell Latitude X300 Cooling Fan Replacement: Schritt 15, Bild 1 von 1
    • Lift the cooling fan out of the laptop.

Abschluss

To reassemble your device, follow these instructions in reverse order.

2 weitere Nutzer:innen haben diese Anleitung absolviert.

Team

Cal Poly, Team 11-20, Maness Winter 2012 Mitglied von Cal Poly, Team 11-20, Maness Winter 2012

CPSU-MANESS-W12S11G20

4 Mitglieder

7 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 1

Letzte 30 Tage: 4

Insgesamt: 1,377