Ersatzteile

Kein Ersatzteil erforderlich.

  1. Rotate the photo printer so that the bottom of the case faces upward.
    • Rotate the photo printer so that the bottom of the case faces upward.

    Kommentar hinzufügen

  2. Use a Phillips #2 screwdriver to remove the three 5.65 mm screws on the bottom panel of the case in a counter-clockwise fashion.
    • Use a Phillips #2 screwdriver to remove the three 5.65 mm screws on the bottom panel of the case in a counter-clockwise fashion.

    Kommentar hinzufügen

    • Rotate the device so that it is upright again. Under the LCD Panel there is a 9.62 mm screw, unscrew using a Phillips #2 screwdriver.

    Kommentar hinzufügen

    • Remove the back panel of the case by pulling directly back.

      • Some carefully applied force may be required to remove this part.

    Kommentar hinzufügen

    • Rotate the photo printer so that the bottom panel faces up once again. Now lift off the bottom panel of the case to access all internal components.

    Kommentar hinzufügen

    • Finally remove the side panel with the ink-cartridge door by holding the right side and pulling backwards with the left side.

      • Caution! The side panel is held in by tabs; don't break these.

    Kommentar hinzufügen

    • Carefully remove the inner components of the device by lifting the inner components up and out of the casing.

    Kommentar hinzufügen

  3. Frohes Fest, frohes Tüfteln
    Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12.
    Frohes Fest, frohes Tüfteln
    Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12.
    • Locate the red and black cable that is connecting the fan to the top of the logic board.

    Kommentar hinzufügen

    • Carefully, remove the red and black cable from the logic board by pulling gently in order to isolate the cooling fan from the device.

    Kommentar hinzufügen

    • Locate the data ribbon that connects the LCD panel to the mother board.

    • Loosen the fasteners next to the ribbon by carefully pushing them away from the white ribbon holder.

      • Once the fasteners are loosened the ribbon should easily slide away from the motherboard.

    Kommentar hinzufügen

    • Locate the clips with multi-colored wires that connect the motherboard to the printing unit.

      • Disconnect both of them by gently pulling them away from the motherboard.

    Kommentar hinzufügen

    • Locate the white ribbon that connects the motherboard to the printing feed.

    • Disconnect the ribbon by gently pulling the ribbon away from the motherboard.

    Kommentar hinzufügen

    • The mother board has changed orientation. Notice the new orientation based on the white data ribbon we removed in the previous step.

    • Locate the black data ribbon that connects the mother board to the printing motors.

    • Disconnect it from the logic board, by gently pulling the wire away from the mother board.

    Kommentar hinzufügen

    • Now unscrew the three screws 7.89mm (counter-clockwise) using a Phillips #1 screwdriver.

    Kommentar hinzufügen

    • Once screws and ribbons are disconnected, you can pull mother board away from the printing unit.

    Kommentar hinzufügen

    • Gain access to the bottom of the top case with a thin horizontal control panel motherboard attached to the bottom.

    • Remove the front panel.

      • The dell top casing should now only have two sides.

    Kommentar hinzufügen

    • Locate the four 7.85 mm screws attaching the control panel motherboard to the top face casing.

    • Use a Phillips Head #1 screw driver to remove the four highlighted screws.

      • NOTE: Make sure removal of front face plate is completed.

    Kommentar hinzufügen

    • Gently lift the horizontal control panel motherboard and square power switch board.

    • Completely detach the motherboard from the face casing.

      • NOTE: Leave the power switch control attached to the main control panel motherboard.

    Kommentar hinzufügen

    • Locate the multi-colored cable that connects the power switch to the control panel motherboard.

    • Detach the cable, power switch is now accessible.

    Kommentar hinzufügen

Ziellinie

Jonathan Mintz

Mitglied seit 04.04.2012

11 Reputation

3 Anleitungen geschrieben

Team

Cal Poly, Team 14-7, Forte Spring 2012 Mitglied von Cal Poly, Team 14-7, Forte Spring 2012

CPSU-FORTE-S12S14G7

4 Mitglieder

6 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 0

Insgesamt: 457