Einleitung

It can be tricky to find all the potential blockages, so this guide will show how to find and then clean all of them.

Ersatzteile

Kein Ersatzteil erforderlich.

  1. Locate the dust cup latch and press down. Pull outwards and up with the handle to remove the cup.
    • Locate the dust cup latch and press down.

    • Pull outwards and up with the handle to remove the cup.

  2. At the bottom of the now vacant dust cup holder, locate the filter assembly and shroud. It is located just above the "Performance Indicator" Pull up on the latch indicated and remove the shroud. Be aware of any dust that may come off of the HEPA filter.
    • At the bottom of the now vacant dust cup holder, locate the filter assembly and shroud. It is located just above the "Performance Indicator"

    • Pull up on the latch indicated and remove the shroud.

    • Be aware of any dust that may come off of the HEPA filter.

  3. Putting the shroud aside, use two fingers on the edges of the filter assembly to lift the rest of it out of its housing. Note the slot that must line up with the filter during reassembly.
    • Putting the shroud aside, use two fingers on the edges of the filter assembly to lift the rest of it out of its housing.

    • Note the slot that must line up with the filter during reassembly.

  4. Use a prying tool, such as a spudger, to separate the foam filter from the larger HEPA filter. As mentioned previously, a lot of fine dust can kick up during this step, especially if your vacuum is extremely dirty. Consider using a mask if necessary.
    • Use a prying tool, such as a spudger, to separate the foam filter from the larger HEPA filter.

    • As mentioned previously, a lot of fine dust can kick up during this step, especially if your vacuum is extremely dirty. Consider using a mask if necessary.

    • The picture shows a pencil being used, which works fine, but take care to not puncture or otherwise damage the foam filter.

    • Set both of these aside with the rest of the filter assembly for cleaning later.

  5. Kostenloser Versand für alle Bestellungen über 100,00 $ oder mit einem Pro Tech Toolkit!

    Schau dich im Store um
  6. Use a Phillips #2 Screwdriver to remove the dust cup shroud. The shroud is cosmetic, but this will make future steps easier.
    • Use a Phillips #2 Screwdriver to remove the dust cup shroud.

    • The shroud is cosmetic, but this will make future steps easier.

    • Remove the shroud by sliding it downwards over the dust cup slowly, working it off, being careful not to let it over-extend.

  7. On the bottom of the dust cup, locate the hinged door. Use the screwdriver to push the two hinge pins in to remove the door.
    • On the bottom of the dust cup, locate the hinged door. Use the screwdriver to push the two hinge pins in to remove the door.

    • Set the door aside for cleaning.

  8. With the hinged door removed, look into the dust cup and locate the two screws holding the cyclonic funnel in place. Use a #2 Phillips Screwdriver to remove them. The funnel will remove easily, place it aside for cleaning when finished. Use a #2 Phillips Screwdriver to remove them. The funnel will remove easily, place it aside for cleaning when finished.
    • With the hinged door removed, look into the dust cup and locate the two screws holding the cyclonic funnel in place.

    • Use a #2 Phillips Screwdriver to remove them. The funnel will remove easily, place it aside for cleaning when finished.

  9. Grip the dust collector with your hand firmly, looking for the twist-lock that attaches it to the top of the dust cup. Twist it clockwise and remove, setting it aside for cleaning.
    • Grip the dust collector with your hand firmly, looking for the twist-lock that attaches it to the top of the dust cup.

    • Twist it clockwise and remove, setting it aside for cleaning.

  10. Rinse the filter shroud off in water. Particulates should come off fairly easy, as they should be small. If not, scrub lightly. Rinse the foam filter off, working the particulates out with water, being careful not to damage the filter. Run water through the HEPA filter in the opposite direction of the airflow. The water should be hitting the side that the foam filter usually is mounted on.
    • Rinse the filter shroud off in water. Particulates should come off fairly easy, as they should be small. If not, scrub lightly.

    • Rinse the foam filter off, working the particulates out with water, being careful not to damage the filter.

    • Run water through the HEPA filter in the opposite direction of the airflow. The water should be hitting the side that the foam filter usually is mounted on.

    • Place all three items somewhere to dry.

  11. Run water through all the dust cup components, especially the dust collector, removing any lodged particulates or hair.
    • Run water through all the dust cup components, especially the dust collector, removing any lodged particulates or hair.

    • Make sure all components are completely dry before reassembly. Especially for the filter assembly, this can take up to a day.

Abschluss

To reassemble your device, follow these instructions in reverse order.

2 weitere Nutzer haben diese Anleitung absolviert.

Kyle Libby

Mitglied seit: 07.04.2014

948 Reputation

7 Anleitungen geschrieben

Team

Cal Poly, Team 7-23, Regan Spring 2014 Mitglied von Cal Poly, Team 7-23, Regan Spring 2014

CPSU-REGAN-S14S7G23

4 Mitglieder

18 Anleitungen geschrieben

Statistik anzeigen:

Letzte 24 Stunden: 1

Letzte 7 Tage: 3

Letzte 30 Tage: 19

Insgesamt: 731