Zum Hauptinhalt wechseln

Disassembling Canon Pixma MP480 Rear and Side Panel

Was du brauchst

  1. Disassembling Canon Pixma MP480 Rear and Side Panel, Rear and Side Panel: Schritt 1, Bild 1 von 2 Disassembling Canon Pixma MP480 Rear and Side Panel, Rear and Side Panel: Schritt 1, Bild 2 von 2
    • Remove the two 7.9 mm screws using a Phillips #1 screwdriver.

  2. Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 2, Bild 1 von 1
    • Lift up the back cover to remove it.

    • You may need to lift firmly as it requires quite a bit of force.

    "quite a bit of force" is almost an understatement, I found 2 clips along the bottom of that rear piece, one at the far left one around the middle (indicated by an arrow on the underside of the machine) - undoing these required much persistence with a screwdriver

    Perhaps Fuzz - Antwort

    Thank you, Perhaps Fuzz. Thank you.

    Marji Zintz -

  3. Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 3, Bild 1 von 1
    • Open the front tray.

  4. Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 4, Bild 1 von 2 Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 4, Bild 2 von 2
    • Open the scanner compartment.

    • Make sure the blue lever locks into place to keep the compartment open.

  5. Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 5, Bild 1 von 2 Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 5, Bild 2 von 2
    • Remove the blue lever from its slot by pushing it back and twisting clockwise.

    • Close the scanner compartment and cover.

  6. Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 6, Bild 1 von 2 Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 6, Bild 2 von 2
    • Pry open the side cover with the plastic opening tool.

  7. Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 7, Bild 1 von 2 Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 7, Bild 2 von 2
    • Flip the printer over so that you are facing the bottom of the printer.

    • Use the plastic opening tool to remove the corner of the side panel from the plastic pin.

  8. Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 8, Bild 1 von 2 Disassembling Canon Pixma MP480 Rear and Side Panel: Schritt 8, Bild 2 von 2
    • Use the plastic opening tool to loosen the side panel from the bottom of the printer.

Abschluss

To reassemble your device, follow these instructions in reverse order.

6 weitere Nutzer:innen haben diese Anleitung absolviert.

Kevin Cole

Mitglied seit: 01/17/13

116 Reputation

1 Anleitung geschrieben

Team

Cal Poly, Team 19-41, Regan Winter 2013 Mitglied von Cal Poly, Team 19-41, Regan Winter 2013

CPSU-REGAN-W13S19G41

4 Mitglieder

6 Anleitungen geschrieben

2 Kommentare

Where is the rest of disassembly?

bill roberts - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 1

Letzte 30 Tage: 14

Insgesamt: 21,120