Ersatzteile

Kein Ersatzteil erforderlich.

  1. With the needle removed, open the device by pulling up on the handle.
    • With the needle removed, open the device by pulling up on the handle.

  2. Push in on one of the arms attached to the K-cup holder plastic housing to remove it from its rails.  The arms are identical for both sides so once one side is free repeat the process for the second side. The plastic is flexible and will not snap with the force applied. Once the arms are removed, the configuration should look like the picture. The K-cup holder housing should be separated from the arms.
    • Push in on one of the arms attached to the K-cup holder plastic housing to remove it from its rails. The arms are identical for both sides so once one side is free repeat the process for the second side.

    • The plastic is flexible and will not snap with the force applied.

    • Once the arms are removed, the configuration should look like the picture. The K-cup holder housing should be separated from the arms.

    My Keurig has white, nylon half-grommets to reduce wear, where the post of each arm slides in its slot. Take care that they do not fall down into the machine and that you do not lose them.

    wheelersthree - Antwort

    That just happened,( lost the grommet), I can hear it but can't get it out from inside the machine. I put everything back together and it is working. One note: may I suggest removing just the k-cup holder then removing the two screws for the top. you can then access the upper part of the hose. after that I used a long tie wrap (pipe cleaner would have been better, (I had given my tobacco pipes and cleaning equipment away last week.) Also I ran a bread tie down the top connection for the hose and into the needle. That is where I found the last of my clog. So now all I need is to find that little plastic piece and it will be perfect but it is working without it

    sandpat76 -

    Getting this part put back together is near impossible. White pieces keep falling off & don't seem to line up correctly with plastic arms. Over 1 hour to get to this point. Frustrating.

    Christina Lemmey - Antwort

    Don't take it apart at this point! Move on to the next step, then it is super easy to remove this front part in the same way but from the bottom pegs, if you want to clean all the small spaces covered in coffee dust and

    Christina Slack - Antwort

    Yes, the arm will break. Apparently after struggling with it for about an hour, it weakened the plastic enough to snap off the left arm of the cup holder. The machine now works, though! I’ll just have to be mindful when I use it. Looking back, I wish I had tried just cleaning out the needle first. Might have saved me significant frustration with the reassembly of this step.

    Kimberly Meyer - Antwort

    I think you need to tell people that the arms with the white roller will break off after all the struggling the left side broke off Thank for the worthless info. Ron Nelson

    Ron , Lynn Nelson - Antwort

    At this point, I skipped remaining steps 13-16, mainly because I felt those steps are too much work to end up trying to “push out” grounds with my fingers (as described in step 16). Instead, I ran water through the mini-K as if I were making coffee—to remove all the grounds that I saw gunked up in the hose. I aimed the hose into a large bowl.

    I ran water through as many times as needed to get water that was completely clear of any grinds—which took about six 8-ounce cups.

    Thanks to others, whose comments helped me as I was going through the previous steps. :D

    shari_thompson1 - Antwort

  3. Kostenloser Versand für alle Bestellungen über 100 $ oder mit einem Pro Tech Toolkit!

    Schau dich im Store um
  4. Use a Phillips #1 screw driver to remove the four 12 mm screws that hold the arm assembly in place.
    • Use a Phillips #1 screw driver to remove the four 12 mm screws that hold the arm assembly in place.

  5. Lift up the arm and pull up the handle assembly. It should easily come off. This white tab falls off easily, remove it and set it aside to ensure it is not lost.
    • Lift up the arm and pull up the handle assembly. It should easily come off.

    • This white tab falls off easily, remove it and set it aside to ensure it is not lost.

    The first picture is a little on the dark side, but I could still tell what you're trying to say in the picture. Maybe make it a little brighter?

    Rubia Siddiqi - Antwort

    The second picture in this step shows the white plastic 'slide guide thinger', it is however upside down. During reassembly make sure to have it the other way so that the handle assembly will stay up when installing a k cup. If not the handle will fall everytime you let it go making for a frustrating coffee going experience especially if your not a morning person. :)

    foxyauto - Antwort

    If your clog is in the other end of the hose, you are out of luck. I had only used my machine about 6 times before it wouldn't dispense. I disassembled the contraption, and stuck a pipe cleaner down the hose. There is no clog. Keurig is sending me a $50 coupon to apply toward a new machine.

    Jill Kozak - Antwort

Abschluss

To reassemble your device, follow these instructions in reverse order.

Andrew Adriance

Mitglied seit: 14.01.2014

1.634 Reputation

7 Anleitungen geschrieben

Team

Cal Poly, Team 17-1, Forte Winter 2014 Mitglied von Cal Poly, Team 17-1, Forte Winter 2014

CPSU-FORTE-W14S17G1

5 Mitglieder

12 Anleitungen geschrieben

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 1

Insgesamt: 51