Zum Hauptinhalt wechseln

Disassembling Olympus Stylus 1010 Case

Was du brauchst

  1. Disassembling Olympus Stylus 1010 Case, Disassembling Olympus Stylus 1010 Case: Schritt 1, Bild 1 von 2 Disassembling Olympus Stylus 1010 Case, Disassembling Olympus Stylus 1010 Case: Schritt 1, Bild 2 von 2
    • Remove the five Phillips #00 bottom and right side panel screws.

    Put a notice on here that the screws are very small and are easy to misplace while disassembling device. Also, while disassembling the device there was only one screw present, where the guide suggested there were three.

    Curtis Reedy - Antwort

    Before beginning, put a note that the camera should be turned off before proceeding.

    Curtis Reedy - Antwort

    Add a note at the beginning of the guide that there are a large number of small screws that should be separated as the steps are completed.

    Curtis Reedy - Antwort

    There's a capacitor .....watch out for it in every step.

    BILL BOYD - Antwort

  2. Disassembling Olympus Stylus 1010 Case: Schritt 2, Bild 1 von 1
    • Remove the right side panel by pulling off the large silver piece.

    There is no reference to removing screws from the right side panel, where it is necessary to remove 2 screws to do so.

    Curtis Reedy - Antwort

  3. Disassembling Olympus Stylus 1010 Case: Schritt 3, Bild 1 von 2 Disassembling Olympus Stylus 1010 Case: Schritt 3, Bild 2 von 2
    • Remove the remaining three Phillips #00 side and front panel screws.

  4. Disassembling Olympus Stylus 1010 Case: Schritt 4, Bild 1 von 1
    • Using your thumb and forefinger, pull off the silver name plate and silver "T-shape" piece.

  5. Disassembling Olympus Stylus 1010 Case: Schritt 5, Bild 1 von 1
    • Remove the black front panel by sliding it towards the lens and then pulling it up off of the camera.

  6. Disassembling Olympus Stylus 1010 Case: Schritt 6, Bild 1 von 3 Disassembling Olympus Stylus 1010 Case: Schritt 6, Bild 2 von 3 Disassembling Olympus Stylus 1010 Case: Schritt 6, Bild 3 von 3
    • Remove the three Phillips #00 screws from the front of the camera.

    • Using a spudger, lift the two tabs to separate the case—one tab on top and one tab on the right side.

    Wrong point of focus for the second picture. What should be in focus is very blurry.

    Curtis Reedy - Antwort

  7. Disassembling Olympus Stylus 1010 Case: Schritt 7, Bild 1 von 3 Disassembling Olympus Stylus 1010 Case: Schritt 7, Bild 2 von 3 Disassembling Olympus Stylus 1010 Case: Schritt 7, Bild 3 von 3
    • Using a plastic spudger, lift up the black clips.

    • Still using the plastic spudger, detach the gold connector strip and white connector strip.

    • Using both hands, pull the camera apart into two pieces.

    There were multiple gold strips, so the one that needs to be pulled should be highlited in the picture.

    Curtis Reedy - Antwort

    in step seven pull up the black bar of the ZIF connectors before pulling out the white or gold ribbons

    Curtis Reedy - Antwort

Abschluss

To reassemble your device, follow these instructions in reverse order.

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

Max McIntyre

Mitglied seit: 01/21/11

526 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team 13-4, Forte Winter 2011 Mitglied von Cal Poly, Team 13-4, Forte Winter 2011

CPSU-FORTE-W11S13G4

6 Mitglieder

12 Anleitungen geschrieben

Ein Kommentar

How did you get the ring around the lens off?? I can't seem to find that step and in all the pictures it's already off

Maureen - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 2

Letzte 30 Tage: 5

Insgesamt: 3,012