Ersatzteile

Kein Ersatzteil erforderlich.

Unscrew the bottom and right side panel screws using a #00 screwdriver. (5 screws) Unscrew the bottom and right side panel screws using a #00 screwdriver. (5 screws)
  • Unscrew the bottom and right side panel screws using a #00 screwdriver. (5 screws)

Put a notice on here that the screws are very small and are easy to misplace while disassembling device. Also, while disassembling the device there was only one screw present, where the guide suggested there were three.

Curtis Reedy - Antwort

Before beginning, put a note that the camera should be turned off before proceeding.

Curtis Reedy - Antwort

Add a note at the beginning of the guide that there are a large number of small screws that should be separated as the steps are completed.

Curtis Reedy - Antwort

There's a capacitor .....watch out for it in every step.

BILL BOYD - Antwort

Remove the right side panel by pulling off the large silver piece.
  • Remove the right side panel by pulling off the large silver piece.

There is no reference to removing screws from the right side panel, where it is necessary to remove 2 screws to do so.

Curtis Reedy - Antwort

Unscrew the remaining side and front panel screws using a #00 screwdriver. (3 screws) Unscrew the remaining side and front panel screws using a #00 screwdriver. (3 screws)
  • Unscrew the remaining side and front panel screws using a #00 screwdriver. (3 screws)

Kommentar hinzufügen

Using your thumb and forefinger, pull off the silver name plate and silver "T-shape" piece. (2 pieces)
  • Using your thumb and forefinger, pull off the silver name plate and silver "T-shape" piece. (2 pieces)

Kommentar hinzufügen

Remove the black front panel by sliding it towards the lens and then pulling it up off the camera.
  • Remove the black front panel by sliding it towards the lens and then pulling it up off the camera.

Kommentar hinzufügen

Remove 3 screws from the front of the camera using a #00 screwdriver. Lift the two tabs to separate the case using a spudger. (one tab on top and one tab on the right side) Lift the two tabs to separate the case using a spudger. (one tab on top and one tab on the right side)
  • Remove 3 screws from the front of the camera using a #00 screwdriver.

  • Lift the two tabs to separate the case using a spudger. (one tab on top and one tab on the right side)

Wrong point of focus for the second picture. What should be in focus is very blurry.

Curtis Reedy - Antwort

Using a plastic spudger, lift up the black clips. Still using the plastic spudger, detach the gold connector strip and white connector strip. Using both hands, pull the camera apart into two pieces.
  • Using a plastic spudger, lift up the black clips.

  • Still using the plastic spudger, detach the gold connector strip and white connector strip.

  • Using both hands, pull the camera apart into two pieces.

There were multiple gold strips, so the one that needs to be pulled should be highlited in the picture.

Curtis Reedy - Antwort

in step seven pull up the black bar of the ZIF connectors before pulling out the white or gold ribbons

Curtis Reedy - Antwort

Using a plastic spudger, lift up the black clips. Still using the spudger, detach the 3 gold wire tape connectors from the inside of the camera.
  • Using a plastic spudger, lift up the black clips.

  • Still using the spudger, detach the 3 gold wire tape connectors from the inside of the camera.

Kommentar hinzufügen

Remove 3 screws from the inside of the camera using a #00 screwdriver.
  • Remove 3 screws from the inside of the camera using a #00 screwdriver.

Kommentar hinzufügen

Using your thumb and forefinger, pull the lens piece straight out from the body of the camera. Using your thumb and forefinger, pull the lens piece straight out from the body of the camera.
  • Using your thumb and forefinger, pull the lens piece straight out from the body of the camera.

Kommentar hinzufügen

Unscrew two screws on the right side of the camera using a #00 screwdriver.
  • Unscrew two screws on the right side of the camera using a #00 screwdriver.

Kommentar hinzufügen

Using a plastic spudger, lift up the black clips.
  • Using a plastic spudger, lift up the black clips.

  • Still using the spudger, detach the gold wire tape connectors from the logic board.

Kommentar hinzufügen

Unsolder the upper right and lower left wires to remove logic board.
  • Unsolder the upper right and lower left wires to remove logic board.

Kommentar hinzufügen

In order to remove the logic board, grab each side of it and pull up using your thumb and forefinger. In order to remove the logic board, grab each side of it and pull up using your thumb and forefinger.
  • In order to remove the logic board, grab each side of it and pull up using your thumb and forefinger.

Kommentar hinzufügen

Abschluss

To reassemble your device, follow these instructions in reverse order.

Max McIntyre

Mitglied seit 21.01.2011

511 Reputation

4 Anleitungen geschrieben

Team

Cal Poly, Team 13-4, Forte Winter 2011 Mitglied von Cal Poly, Team 13-4, Forte Winter 2011

CPSU-FORTE-W11S13G4

6 Mitglieder

6 Anleitungen geschrieben

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 0

Letzte 7 Tage: 1

Letzte 30 Tage: 5

Insgesamt: 2,677