Diese Anleitung zeigt dir, wie du den 3,7 V Lithium Akku im Dual Shock 4 ersetzen kannst.

  1. Entferne die vier 6,0 mm PH00 Schrauben, die die hintere Abdeckung am Controller befestigen.
    • Entferne die vier 6,0 mm PH00 Schrauben, die die hintere Abdeckung am Controller befestigen.

    • Die Schrauben nicht mit Gewalt lösen, da dies die Gewinde dauerhaft beschädigen kann, wodurch die Entfernung unmöglich wird.

    Kommentar hinzufügen

  2. Beginne am linken Handgriff:
    • Beginne am linken Handgriff:

      • Quetsche den linken Handgriff um ein Öffnungswerkzeug einsetzen zu können.

      • Zwänge ein Öffnungswerkzeug in die Öffnung und schiebe es in Richtung Joystick.

      • Drücke das Werkzeug nach unten bis der Deckel abspringt.

    • Wiederhole das Ganze für den rechten Handgriff.

    Shoulders are where L1/L2/R1/R2 are, not the %#*@ handles. Confusing instructions.

    foxhoundunit89 - Antwort

    Quick tip: Be VERY careful at this step not to dislodge the tiny spring attached to the L2/R2 buttons. While removing the cover, it's easy to pull off either L2/R2 button. Inadvertently pulling off either button will also remove the tiny spring as well. While not too difficult to reassemble, it's not obvious where the spring goes as the spring is almost completely hidden along the side of the button (on the inside).

    I just successfully completed analog stick replacements for two controllers. I completed the first repair without any trouble but managed to dislodge (and almost lose) the spring on the second time around. Needless to say, I spent some time trying to figure out where the spring is supposed to go (no photos of this anywhere). By sheer luck, I figured it out on my own. :)

    Good luck and take your time--especially the first time!

    Michael Whang - Antwort

    couldn't have posted pics for me? :D

    kimsballs -

    Golden tip but I would add a thing or two.

    Most probably both triggers R1&R2 will stay in lower half of the pad case with springs hanging there.

    You must take them of their lower case sockets before assembly and fit them bellow L1&L2

    When you feel click when fitting them and spring works like on normal assembled pad you're done.

    If thats not the case do not try to assemble lower casing half as triggers will not work properly.

    Simon -

    if you lost the springs unfortunately, the triggers would still work but it is harder to get to the precise digital press. In other words you will have hard time to create a light press than a hard press.

    meaningless -

  3. Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    Frohes Fest, frohes Tüfteln
    Pack's ein, pack's aus, pack's an: Erhalte 12 € Rabatt auf deinen Einkauf ab 50 € mit dem Code FIXMAS12
    • Zwänge das Öffnungswerkzeug in den Spalt zwischen den Gehäusehälften und drücke ihn nach unten um das Gehäuse in der Nähe folgender Knöpfe zu öffnen:

      • Teilen Knopf

      • Optionen Knopf

    • Nimm die Plastikdeckel auseinander, achte darauf, dass immer noch Flachbandkabel daran hängen.

    • Drei kleinere Teile fallen dabei oft ab. Damit du sie nicht verlierst, musst du für eine aufgeräumte Arbeitsfläche sorgen.

      • Zwei Federn an den Auslösern.

      • ein graue Verlängerung für den Reset Knopf.

    You can't just pull the casing halves apart. There is a plastic bar that is part of the casing and separates the L1 and R1 buttons from the L2 and R2 buttons. To get this loose, pull the casing outward perpendicular to the L and R buttons until you can slide the L2 and R2 buttons from behind the plastic bar.

    dzturbd - Antwort

    SO yesterday replaced the thumb stick on my controller, and now the R2 button is stuck, know any way to remedy this?

    ScootsMcgoots -

    I know you put a warning, but I lost the grey reset button extension. Any idea where to get a replacement part?

    miamiman77 - Antwort

    Hey, not even sure when you wrote this, but wanted to share my solution for this problem. I lost one of my reset button rubber pieces when I was doing a different repair, and found that a standard bamboo skewer is just about the perfect diameter to function as a replacement. Just cut it to the proper length and you should be able to get it in there and get your reset functionality back.

    tcbrekke -

    You don't really need it. A long paper clip will work fine.

    Ron Smith - Antwort

    I've removed and changed all buttons all seemed ok but now the options and share button don't work, as in when I pressed them down there is no longer a click (bounce) I'm certain it's back in the correct place and I don't think they can be put the wrong way up, does anyone have any advice please :)

    Rachel - Antwort

    My share button stopped 'clicking'. When I stripped the controller down I noticed a small copper coloured dimple on the motherboard was depressed instead of proud like the one for the options button. With bluetack I was able to pull it out but each time I tested it with my finger it clicked once and stayed depressed. I don't think there is a permanent solution to this as it's probably metal fatigue or similar so i put a tiny bit of blue tack overy the dimple so the plunger could push that bit further and hopefully pull it out each time. Seems to work as I reassemble the controller. Fingers crossed it holds out a while! I'd love to know if someone else had a different solution.

    The5HD -

    I had an extra part, and it wasn’t gray. Thank goodness for the picture of the black one. It’s rubbery. The small end should be inserted down towards the gold colored spot. It’s next to the word RESET on the mobo.

    J Coyote - Antwort

    When reassembling: If, like me, your R2/L2 buttons stayed with the bottom of the controller when you took it apart, it will be impossible to reassemble and get the tiny springs back in place.

    To remedy, remove the buttons, and attach them, with the springs correctly placed, to the top of the controller. There are two tiny grooves, one on the button, and one on the controller top, into which the spring fits.

    Jeff Human - Antwort

    Jeff, we owe you a six pack for this comment.

    James Goldie -

    Thank You!! The spring came out and I looked for a way to reinsert it. So I led a thread through its opening (so it couldn´t jump away), and compressed it with pliers. So it was easy to put it in.

    VauWeh -

    • Löse das Flachbandkabel an der Hauptplatine, welches die beiden Hälften des Controllers verbindet, indem du es mit deinen Fingern gerade herausziehst.

      • Beachte, dass die Ausrichtung des Kabels in die richtige Richtung zeigt, wenn du es wieder verbindest.

    • Nachdem du die beiden Teile getrennt hast, lege das Oberteil zur Seite.

    can you share the battery dimension?

    luxusmirajane - Antwort

    • Löse den Akkustecker vorsichtig mit einer stumpfen gewinkelten Pinzette, indem du diese an den Seiten des Steckers ansetzt.

    • Wenn der Stecker von der Hauptplatine gelöst ist kannst du den Akku herausheben.

    • Zu ruckartiges Herausziehen des Steckers kann die Plastikteile des Steckers verbiegen.

    For the replacement battery I found that the Turnigy 2000mAh 1S 1C Lipo w/ 2 Pin JST-PH worked perfectly while also being a budget option at only $2.54 USD before shipping. However ONLY INSTALL AFTER CHANGING THE POLARITY OF THE CONNECTOR, this can be done with a pin or craft knife with relative ease. After doing this the controller has doubled in battery life. It required no modification to the controllers internals only extra care to ensure the longer cables didn’t get pinched in reassembly.

    Ryan - Antwort


Um dein Gerät wieder zusammen zu setzen folge den Schritten in umgekehrter Reihenfolge.

92 weitere Nutzer haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:


Diese Übersetzer helfen uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Beginne zu übersetzen ›


Mitglied seit 21.01.2014

5.095 Reputation

4 Anleitungen geschrieben


Cal Poly, Team 6-21, Maness Winter 2014 Mitglied von Cal Poly, Team 6-21, Maness Winter 2014


4 Mitglieder

25 Anleitungen geschrieben

My Dualshock 4 wont turn on after the battery replacement.

Any idea on why this happened?

Alexander - Antwort

have you tried to charge it?

Mohamed Aden -

I had a problem with my console but with your guide it is possible to solve this one I think.

Praska - Antwort

The only replacement battery option listed in the 'relevant parts' section of the guide is for a used battery. Here is a a link to a new replacement battery for those that don't want to do this again in a few months. It is higher capacity than the OEM battery (1300mAh instead of 1000mAh) so it will last longer. Hope this helps!

New Replacement Battery for Dualshock 4 Controller

Mike - Antwort

My samsung galaxy tab 2 7inch screen goes black help

clarissa owens - Antwort

I found a replacement battery here, you have to mod the tray a little, but it works like a champ and doubles the life.


binazriel - Antwort

The x button on my controller want working properly so I ordered new rubber mounts. I followed the guide, taking my time to make sure I didn't damage anything.

With the new rubber in place I put everything back together and the controller was working fine but now I've realised it doesn't charge. The battery goes completely dead and switches off. If I then connect it with usb cable it doesn't charge but will turn on the controller for maybe 10 seconds before switching off again.

Anyone any idea what is going on? Thanks.

Kenny - Antwort

my controller is not starting today

Harry Patidar - Antwort

Did this fix to the letter, controller works now but the light bar does not and I'm unsure if it charges. It shows it's fully charged. Could it be that the micro-usb connection is frapped?

the00brotherhood - Antwort

Ok, so it shows it’s fully charged on the PS4 but the light on the controller is out if I’m reading you right. Method I would use… connect the controller to your computer with a wired cable (eliminating the PS4 from the equation).

Check Device Manager in Windows or System Report on a Mac. Does it show your controller?

Yes = USB port on controller is fine, you may have damaged the LED on it during the repair.

No = USB port may be damaged or the cable may be fried.

Your problem doesn’t seem like it would have anything to do with the USB port. If it works but with no lighting, you should be ok unless you use the controller with the PS4 camera.

Brad S -

The battery outlet got ripped off. Can it still be fixed?

nextinline3900 - Antwort

Anything can be fixed. But without knowing how severe the damage is it’s hard to say how difficult it would be, although it may involve cannibalizing another controller. At this point it may be cheaper to just purchase a new Dual Shock.

Brad S -

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 99

Letzte 7 Tage: 646

Letzte 30 Tage: 3,038

Insgesamt: 152,594