Zum Hauptinhalt wechseln

Fairphone 2 Rückkamera-Modul austauschen

Was du brauchst

  1. Fairphone 2 Rückkamera-Modul austauschen, Slim Case: Schritt 1, Bild 1 von 3 Fairphone 2 Rückkamera-Modul austauschen, Slim Case: Schritt 1, Bild 2 von 3 Fairphone 2 Rückkamera-Modul austauschen, Slim Case: Schritt 1, Bild 3 von 3
    • Wähle eine Ecke an deinem Slim Case und gehe mit den Daumennägeln zwischen die beiden Teile.

    • Ziehe den hinteren Teil nach oben, um die kleinen Clip-Verbindungen zu lösen.

    • Nimm den hinteren Teil ab.

  2. Fairphone 2 Rückkamera-Modul austauschen: Schritt 2, Bild 1 von 3 Fairphone 2 Rückkamera-Modul austauschen: Schritt 2, Bild 2 von 3 Fairphone 2 Rückkamera-Modul austauschen: Schritt 2, Bild 3 von 3
    • Gehe mit dem Daumennagel zwischen den vorderen Teil des Slim Case und dem Gehäuse des Fairphones.

    • Trenne die Clip-Verbindungen des vorderen Teils, indem du es zur Seite zieht und gleichzeitig gegen das Display drückst.

  3. Fairphone 2 Rückkamera-Modul austauschen: Schritt 3, Bild 1 von 1
    • Nimm den vorderen Teil des Slim Cases zur Seite.

  4. Fairphone 2 Rückkamera-Modul austauschen, Akku: Schritt 4, Bild 1 von 3 Fairphone 2 Rückkamera-Modul austauschen, Akku: Schritt 4, Bild 2 von 3 Fairphone 2 Rückkamera-Modul austauschen, Akku: Schritt 4, Bild 3 von 3
    • Drücke die Batterie leicht nach oben.

    • Nimm die Batterie nach unter heraus.

    It isn't necessary to remove the rim if all you are doing is changing the battery. That becomes necessary if you are to proceed farther into the phone.

    It might be good to begin by saying switch the phone off. The Fairphone is for everybody and most will have no experience of disassembling electronic devices.

    Jim Kinnibrugh - Antwort

  5. Fairphone 2 Rückkamera-Modul austauschen, Display-Einheit: Schritt 5, Bild 1 von 3 Fairphone 2 Rückkamera-Modul austauschen, Display-Einheit: Schritt 5, Bild 2 von 3 Fairphone 2 Rückkamera-Modul austauschen, Display-Einheit: Schritt 5, Bild 3 von 3
    • Nachdem der Akku herausgenommen wurde entriegelst du die Display-Einheit.

    • Stelle hierfür die beiden blauen Schalter auf die innere Position.

    • Schiebe die Display-Einheit nach unten.

    Being technically nervous I couldn't do this. I didn't know how much pressure, pull or push was required.

    Roger Halford - Antwort

    After I'd watched the video my confidence increased!

    Roger Halford - Antwort

    It was a bit stiff and not so easy.

    M ichael Cross - Antwort

    I have not this easy access to the two blue switches. How Can I do that?

    Anne - Antwort

    Super, nachdem ich’s im Video gesehen habe, war es supereasy, vielen Dank!

    Imke - Antwort

    You don´t mention taking the rim off the display first. That stymied me completely. Do add that to your otherwise clear and helpful instructions. Best wishes - Walt Patterson

    Walt Patterson - Antwort

    This guide is based on the old bumper made in one piece. We should update to the sandwich bumper with a top and bottom part.

    Tobias Isakeit -

    I agree. Took a while to figure that one out!

    Jenny White -

    Sorry, I can not slide away the display assembly to change the main camera module. The 2 blue switches seem to be locked. Cristiano, Italy

    Cristiano Gillardi - Antwort

    I replay to myself: I did it at last! ! But it was very, very, very, very hard!

    Cristiano Gillardi -

    Can’t get any movement at all on screen been trying for over an hour and others too ! there is no way to grip it as its so slippery have tried putting as much presure as possible on display by pushing far end of it with thin plastic implement and endless wiggling and pressing of every possible part of lower case no joy ! feels like its attached at mid sides. Elinor Rivers

    Elinor Rivers - Antwort

    try sliding along the display while applying some pressure two or three times. it worked really easily for me

    Elisa Werner - Antwort

    I could slide the display case off very easily after watching the video, but when it came to doing the sequence in reverse I was fiddling about for ages trying to ‘slide’ it back on, until I realised this just wasn’t going to work and needed to click it back into place. Posting here in case this is helpful for others.

    Rachel Neat - Antwort

    • Eine weitere Möglichkeit, die Display-Einheit aufzuschieben.

    Impossible de déplacer l'écran vers le bas chez moi. Je n'ose pas forcer... c'est normal?

    benbahmedf - Antwort

    I can not slide the display assembly. Some help?

    Laura Ivorra - Antwort

    The display sits very tight.

    So you need to gently apply a little force to slide it open the first time.

    It is hard to get a good grip on the two parts for a successful "magic move".

    Tobias Isakeit - Antwort

    Leider kann ich weder mit "little force" noch mit "much force" das Display nach der Entriegelung bewegen. Wer kann mit mehr Details helfen?

    Christine Heckmann - Antwort

    It did work for me. Make sure, you have unlocked the blue switches in step 3 (sorry, had to mention that). if you can't get a grip, you might try to lay a ruler or two credit cards on top of each other on a table that is tight at the wall,

    - place the ruler/credit cards on the table and just attaching the wall

    - place the PF2 with the display upside down on the table in front of the ruler/credit cards with the blue switches towards you and the headphone plug attaching the ruler/cards.

    - then gently but with increasing force push your two thumbs towards the top of the main FP2 unit (or use more fingers to push both in the centre as well as on the two edges). make sure you push horizontally and that the ruler is not higher than the border of the display unit (1.5-2 mm).

    (hope i could explain myself in and understandable way! ;-) )

    metaworx - Antwort

    Thank you a lot ! This worked for me.

    Nicolas Dudermel -

    Thanks, it worked for us as well.

    deRahier -

    great tip! Thanks so much

    Matthew Kelly -

    Really helped! This way finally worked for me. Thanks :)

    Imogen Michel -

    thank you !!

    Claire Hahn -

    Perfect Metaworx, it worked for me as well :)

    siohdk - Antwort

    Your nails are slightly long? You are lucky. Hold the phone with the screen on your right palm with the blue bits facing your body. Make sure your fingernails are holding the top of the screen. Push the back of the phone with your left hand. It worked for me.

    Askateth - Antwort

    Mit einer alten Haltekarte für SIM Cards als Hebel habe ich das Display vorsichtig abgeschoben

    Joachim - Antwort

    Unglaublich fair, dass ich mich mit diesem Kack alleine beschäftige - wenn ich so weitermache, werde ich demnächst die Trümmer meines Fairphones wahrscheinlich durch Ungeschicklichkeit so beschädigen, dass es unbrauchbar ist!

    Ralf Kiefer - Antwort

  6. Fairphone 2 Rückkamera-Modul austauschen: Schritt 7, Bild 1 von 1
    • Nimm die Display-Einheit ab.

  7. Fairphone 2 Rückkamera-Modul austauschen, Rückkamera-Modul: Schritt 8, Bild 1 von 2 Fairphone 2 Rückkamera-Modul austauschen, Rückkamera-Modul: Schritt 8, Bild 2 von 2
    • Entferne die drei Kreuzschlitzschrauben die auf dem Modul mit blauen Kreisen markiert sind.

    • Das Modul sollte nun ein wenig abstehen aufgrund der darunter liegenden Federkontakte.

    Danke! Geht alles gut. Nur einen so kleinen Schraubenzieher, den hat ja nicht jeder :-( . Das Geht dann auch mit einem Schweizer Messer, mit der Spitze der großen Klinge. Vorsichtig auf die Schraube aufsetzen und leicht - ohne Kraft - drehen. Sonnige Grüße au Berlijn

    solar - Antwort

    Das Thema ist doch die Demontage der Rückkamera. Hier wird aber die Frontkamera demontiert. Wenn man einmal so weit ist, kann man die 2 Schrauben der Rückkamera auch herausdrehen und das Modul entnehmen. Gruß - Ralf

    Ralf Dassler - Antwort

    Nein nein, das ist die Rückkamera. Also die mit 8 MP, die auf der Rückseite des Telefons filmt.

    Die Frontkamera ist die auf der Seite des Displays. Ist nur eine Definitionssache.

    Siehe Beschreibung der Komponenten hier: Fairphone 2

    Ulrich Schwar -

  8. Fairphone 2 Rückkamera-Modul austauschen: Schritt 9, Bild 1 von 1
    • Nimm das komplette Modul heraus.

    Is it possible to do this last step without the pliers?

    Mathilde Pellerin - Antwort

    Definitely, yes.

    Tobias Isakeit -

    merci, ça marche !

    Jehan d’Ek

    jean.dekkers - Antwort

    This taking out the camera module and putting it back in again has worked for me! I wonder for how long. Let’s see!

    Jenny White - Antwort

    Same for me: taking it out and putting it back ‘repaired’ it. Love the Fairphone!

    David Chapman - Antwort

Abschluss

Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.

Informationen zum Thema "Was mache ich mit dem alten Modul" sind auf der FairPhone-Supportseite und im FairPhone-Forum zu finden.

71 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Tobias Isakeit hilft uns, die Welt in Ordnung zu bringen! Wie kann ich mithelfen?
Hier starten ›

Tobias Isakeit

Mitglied seit: 03/31/14

117.296 Reputation

188 Anleitungen geschrieben

Team

Master Techs Mitglied von Master Techs

Community

322 Mitglieder

2.521 Anleitungen geschrieben

22 Kommentare

Alles gut - hat wunderbar funktioniert, insbesondere dank des Videos für Schritt 4

Walter Strohschein - Antwort

Heel snelle levering van mijn nieuwe camera!

Het was ons (mijn man) vast niet gelukt zonder de goede begeleidende filmpjes! 

Betty Bol

Betty - Antwort

die Variante mit slim case ist noch nicht berücksichtigt

Ansonsten: super Anleitung

W. Koch - Antwort

Hat prima funktioniert dank einfacher Anleitung und einfacher Bauweise.

Christian Heider - Antwort

Geschafft! - Schritt 4 war beim Slim Case nicht so einfach, aber nach ein paar Minuten hatte ich es raus. Ich frage mich bloss, was ich nun mit der alten Kamera mache..? Kann man die zurückschicken? Gibt es dazu irgendwelche Infos? Danke für die Anleitung und allfällige Infos bezüglich “Zukunft der alten Kamera” ;-) !

Claudia Serena Herrmann - Antwort

Hallo Claudia, Gratulation zur gelungenen Reparatur. Bezüglich alten Modulen kannst du hier auf der Seite von Fairphone mal vorbei schauen: https://support.fairphone.com/hc/en-us/a...

Tobias Isakeit -

cool, einmal auf und zu, und es läuft wieder! Besten Dank!

Theater Carnivore - Antwort

Danke – hat super funktioniert!

Kaethe H. - Antwort

Great instructions - very easy to use. Thanks a lot!

Damion Milliken - Antwort

sehr gute Anleitung, vor allem auch durch das Video. Beim Slim case muss man aber das vordere Rahmenteil auch runternehmen, was ich aber schnell rausgfunden habe. Die Kamera funktioniert jetzt wieder einwandfrei und bringt vorläufig keine Fehlermeldungen mehr.

Katissa St - Antwort

I’ve done it and my rear camera works again! Thanks a lot!

martaaa.meloni - Antwort

Anleitung sehr gut - insbes. durch das Video. Leider ist in der Anleitung die Notwendigkeit des Entfernens dss vorderen Rahmenteils nicht beschrieben. Das muß aber runter, sonst kommt man nicht weiter! Ich hab’s nach einigem hin u. her herausgfunden. Die Kamera funktioniert jetzt v o r l ä u f i g einwandfrei; sie bringt keine Fehlermeldungen mehr. Ich hoffe, dass das bleibt so!

Danke jedenfalls für die Beschreibung!

Ludwig Eichinger - Antwort

Danke für den Hinweis. Wir haben den guide aktualisiert, damit er nun auch zeigt, wie die zweiteilige Schale abgenommen wird. Schön zu hören, dass es trotzdem geklappt hat.

Tobias Isakeit -

Vielen Dank für die tolle Anleitung!! Ich habe es super hingekommen, obwohl ich wirklich etwas nervös war ;)

Christin - Antwort

My camera is working again. Very clear instructions.

riannewitteveen64 - Antwort

Super Anleitung, vor allem das Video um den Rahmen zu entfernen. Tolles Gefühl, wenn es nachher wieder funktioniert und man hat es selber geschafft! Danke!

Melanie Vosseler - Antwort

How tight should those screws be? Camera is now working again cheers!

nosleavesandymatrix - Antwort

Vielen Dank für die Anleitung.! Habe das Handy zum ersten Mal auseinander gebaut und war etwas nervös. Aber mithilfe der Anleitung war es ganz einfach und jetzt scheint meine Kamera wieder zu funktionieren :)

Siebel-Neumann - Antwort

Super! Stap voor stap; heldere taal; duidelijke plaatjes; ook info over ‘what if?’ Geeft gevoel dat je het zelf kunt. > Camera gefixt zonder verzendkosten etc. Echt Fair!

Johan Schelling - Antwort

Thanks so much - followed these instructions and my rear-facing camera now works beautifully again!

Catherine Black - Antwort

Hurra! Dank der Anleitung habe ich meine erste Reparatur-Aktion am eigenen Handy geschafft. Nun bin ich gespannt, wie viele Jahre mir das gute Stück weiter treue Dienste leisten wird. Danke für die super Erklärung! Auch mir hat das Video den entscheidenden Schubs gegeben, mit Schmackes dran zu gehen.

y.z. - Antwort

danke für die einfache und gut verständliche anleitung. ich keine zehn minuten gebraucht um die kamera auszutauschen.

Ueli Tschamper - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 2

Letzte 7 Tage: 4

Letzte 30 Tage: 10

Insgesamt: 121,702