Zum Hauptinhalt wechseln

Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra

Was du brauchst

  1. Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra, Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 1, Bild 1 von 3 Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra, Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 1, Bild 2 von 3 Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra, Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 1, Bild 3 von 3
    • Der Anschluss des Temperaturfühlers befindet sich unter dem Handschuhfach. Du kannst den weißen Stecker unter dem Armaturenbrett sehen.

    • Der Temperaturfühler dient dazu, den Verdampfer vor dem Einfrieren zu schützen. Dazu misst er die Temperatur und schaltet den Kompressor ab, wenn der Verdampfer eine Temperatur unter ca. 40 Grad F erreicht, damit dieser auftauen kann.

    • Finde den Kompressor der Klimaanlage. Die Kupplung ist der mittlere Bereich. Wenn die Kupplung eingeschaltet ist, dreht sich der mittlere Bereich. Er wird durch den Temperaturfühler abgeschaltet, um das Einfrieren des Verdampfers zu verhindern.

    • Diese Werkzeuge brauchst du für diese Anleitung.

  2. Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 2, Bild 1 von 1
    • Teste den Temperaturfühler, indem du den Motor und die Klimaanlage einschaltest.

    • Bei Verwendung eines Voltmeters (eingestellt auf DC Volt) weist das grün/orange-Kabel eine Batteriespannung (ca. 13,5V) von Sicherung Nr. 29 im Sicherungskasten unter der Haube auf.

    • Das blaue Kabel hat Batteriemasse von der AC-Steuereinheit.

    • Der wichtigste Draht ist der blaue/schwarze Draht. Das Voltmeter zeigt bei eingeschaltetem Temperaturfühler weniger als 0,5 Volt an (Temperatur über 7 Grad C). Er zeigt bei ausgeschaltetem Temperaturfühler (Temperatur unter 4,4 Grad C) nominal 4-5 Volt an.

    • Während des Anfangsbetriebs liegt die Temperatur am Verdampfer über 7 Grad C und das Voltmeter sollte weniger als 0,5 Volt anzeigen. Wenn die Temperatur des Verdampfers unter 4,4 Grad C liegt, zeigt das Voltmeter 4-5 Volt an, wodurch der Klimakompressor ausgeschaltet wird. Dies verhindert das Einfrieren des Verdampfers.

    • Wenn dein Temperaturfühler beim ersten Einschalten 4-5 Volt anzeigt, ist er defekt und muss ersetzt werden.

    Hello good day. I tested my ac thermistor the blue/black wire reading is above 0.5v when I just turn on the a/c. Is the thermistor bad already? Thanks

    type1028 - Antwort

    ,if I unplug the bad coupling and plug up the new one will the unit work then before take it apart???

    Jimmy Parker - Antwort

  3. Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 3, Bild 1 von 2 Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 3, Bild 2 von 2
    • Der Austausch des Temperaturfühlers erfordert die Demontage des Handschuhfachs.

    • Entferne die vier oberen und die beiden unteren Schrauben wie angegeben.

  4. Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 4, Bild 1 von 3 Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 4, Bild 2 von 3 Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 4, Bild 3 von 3
    • Mit einem Kreuzschlitzschraubendreher drei Schrauben entfernen (wie durch die orangefarbenen Kreise angezeigt).

    • Mit einem 10mm Steckschlüssel vier Schrauben entfernen (wie durch die blauen Quadrate angezeigt). Die beiden rechten sind gut sichtbar, aber die beiden linken sind schwer zu sehen und befinden sich hinter der Abdeckung.

  5. Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 5, Bild 1 von 3 Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 5, Bild 2 von 3 Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 5, Bild 3 von 3
    • Hier kann es jetzt schwierig werden kann. Natürlich wäre es der richtige Weg, das System komplett zu leeren und den Verdampfer zu entfernen, aber mit ein wenig Geschick kann man ihn in 10 Minuten austauschen.

    • Öffne die Verdampferabdeckung, indem du sie in der Mitte teilst. Ich habe eine Federklammer anders herum benutzt, um die Hälften auseinander zu spreitzen.

    • Mit einer langen Spitzzange den Temperaturfühler vorsichtig aus den Verdampferlamellen herausziehen.

  6. Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 6, Bild 1 von 2 Fehlersuche und -behebung bei der Klimaanlage des Nissan Xterra: Schritt 6, Bild 2 von 2
    • Ich habe einen neuen Temperaturfühler für 52 Dollar beim Fachhandel gekauft. Den neuen Temperaturfühler mit der Spitzzange in die Verdampferlamellen einsetzen.

    • Das Entfernen des Steckers von der Halterung war schwierig, ich habe dabei die Halterung zerbrochen. Zum Glück wurde mit dem neuen Temperaturfühler auch ein neuer Montagebügel mitgeliefert. Man benötigt eine kleine Blechschraube, um den neuen Montagebügel in einem Loch neben dem vorhandenen Montagebügel zu befestigen.

    • Ein Loch ist für die Montage der neuen Halterung vorgesehen.

    Be careful when installing the new one, the attachment arm can break fairly easy if you force it.

    Tom - Antwort

Abschluss

Um die Klimaanlge wieder zusammenzusetzen, folge dieser Anleitung in umgekehrter Reihenfolge.

33 weitere Nutzer:innen haben diese Anleitung absolviert.

Besonderer Dank geht an diese Übersetzer:innen:

en de

100%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Doug Layne

Mitglied seit: 06/21/12

1.195 Reputation

1 Anleitung geschrieben

26 Kommentare

Excellent information. My 2003 Xterra was acting up with the AC compressor kicking off and on when the vehicle got up to temperature. One mechanic told me the compressor was knocking and ready to fail. I found out that it was simply overcharged with Freon after a high pressure AC hose replacement. It has worked fine for two years now after getting the Freon right.

Glenn - Antwort

Article by Doug Layne was the answer to my 2000 Nissan Frontier Crew Cab. The Thermo Amplifier was the cause of my problem. A/C works like new. Also make sure you clean inside the unit. I have no idea how so much dirt got into the unit. Must be poor design.

Thanks Doug from another Doug

Doug Wacha - Antwort

What was yours doing and what did you do to fix it.I just got mine 01 and the compressor is working but not cooling much.please help.

jbegleybuild -

What was yours doing.my compressor is working and the garage charged it but not getting cold.they said they thouhht it was the expansion valve.what do you think

jbegleybuild -

In step 6, part of the sentence is cut off, what should it say: "They provided a hole for you to mount the new bracket. ( I guess they al"

Karen Strong - Antwort

This info was awesome! I was having the same problem ( cold air and when you shut the car off it might not come back for 10 - 15 min after restart. got an ac thermistor amplifier and did the install as shown ( great pictures and info ) and problem is fixed. Thanks for sharing . Wife drives the xterra and is very happy :) :)

rkcarcare - Antwort

What if you don't pick up any volts from the blue/black wire?

Eddie luna - Antwort

My 2003 Xterra was having same issue. Replacing thermistor was the fix but 2003 Xterra used a two wire component instead of three. Nissan PN 27723-8J000.

ben1542 - Antwort

My 2002 Xterra AC worked intermittently the past two summers. It would often start fine in the morning but not work after a couple of stops. I could hear the solinoid clicking but just couldn't get the cold air to come on again. A mechanic said it needed a new clutch/compressor unit. Fortunately my son was able to replace the thermistor using your instructions. It works like new now - and at a savings of at least $600. If I'd gone to the expense of replacing the unit, the problem would still exist. Thank you for saving us a bundle!

Connie - Antwort

2004 frontier replace all of my a/c component holds vacuum got the freon ,check all of the relays and still the compressor still no engaging comes on sometimes please help.

amartell79 - Antwort

How do you release the thermistor plug from under the dash? it seems like it is screwed in place and doesn't want to release from the dash

tom - Antwort

If you were to recharge a ac using a ac recharge on a 2013 xterra what port would you use the low

ac port or the evap test booster?

Kyle - Antwort

Where is the acc compress located on a 2003 Nissan xterra

onealpat.5 - Antwort

I think it is the same as my 2000 Frontier. Looking at the engine its on the right side.

The pulley looks different that the others because of the clutch.

Russ -

What if you have 12 volts on the blue and black wire? I replaced my thermostor and still same issue. The new one looks different though.

Russ - Antwort

Worked on my Nissan 2000 Xterra,,, had tried other stuff with no success ,

morajuan80@gmail.com - Antwort

So far this seems to have fixed my intermittent cooling issue on my 2002 Frontier.

I had to take out the middle parts of the dash as well around the dials, I needed more room to work. It’s a tight area to work in.

even so, I broke the connecting arm on my first attempt of putting the new one in. Takes patience, and don’t force it. The second attempt went much better. $30 part at O'Reilly.

thanks for posting this! Nicely done

Tom - Antwort

mingalarpar friends

mg myo - Antwort

Do you think this is too ambitious for an amiture???

smudgeandnatthecat - Antwort

I have a 2001 Nissan Xterra that is having the same issue. The compressor clutch kicking off/ on intermittently. Then, Stays off & starts blowing just warm air. It has a brand new Condenser, Compressor, Low Pressure Line. And, Full of Freon. So, I ordered a new Thermistor(Nissan PN: 27675-9Z000). I ordered from Amazon. I hope it's the correct one. And, That it fixes the issue I'm having. Because, This Oklahoma Heat & Humidity is horrible!!

carver_jm1980 - Antwort

Thank You! Great Information!

iamago - Antwort

In step 2 testing with a multimeter do you only need to stick the positive probe into the wire terminals? Thanks in advance!

dkgoodman - Antwort

The issue i am having is the a.c. will blow cold air then hot air… and after a few minutes cold again..

any advise.

manny ramirez - Antwort

With your guidance I got the part from Carid.com <$30. Used the reverse clamps as suggested! Wrapped my left wrist and top of hand with blue painters tape to reduce chance of getting cut and it worked great! Thank you, my AC is now blowing COLD!!!

Victor Kan - Antwort

This is very good detail process specifically about measuring voltage. I was able to get part replaced and AC is working now. Thank you

Nimpat - Antwort

Hey guys! I'm having overheating only when I cut on the AC. Just checked thermistor with multimeter and it's faulty. Will replacing it help my truck to stop overheating and leaking from the condenser?

Tyler Mosteller - Antwort

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 3

Letzte 7 Tage: 38

Letzte 30 Tage: 176

Insgesamt: 174,810