Zum Hauptinhalt wechseln

Einleitung

This guide will give step by step instructions on how to remove and replace both speakers in a Samsung Galaxy Tab S 10.5.

  1. Place the plastic opening tool into the SD card slot or charge port. Try in an upward motion until you see a separation between the tablet and back cover.
    • Place the plastic opening tool into the SD card slot or charge port.

    • Try in an upward motion until you see a separation between the tablet and back cover.

  2. Work around the entire device by sliding the plastic opening tool around the rim.
    • Work around the entire device by sliding the plastic opening tool around the rim.

    • If this is the first time, it will be hard to separate the back cover from the tablet.

    • The clips are approximately 5 cm apart. While working around the device, the clips will make a dislocating sound when disconnected.

    It is not necessary to remove just the white part under penalty of breaking the pins, it is necessary to remove the back with the colored outline of the tablet

    paquito - Antwort

  3. Remove the back cover once all links have been separated.
    • Remove the back cover once all links have been separated.

    • Be careful when touching any of the internal components of the tablet.

    This is the wrong method to open it! You have to open it beetween the front-Display and the golden rim.

    agnuz6569 - Antwort

    I’ve taken the back cover off my Samsung tablet, and in the process I have torn one of the little orange plastic connectors that are attached to the back cover. The connector I’ve damaged is the second one in on top left in the picture above. Can you please tell me if I need to replace this before I can get the tablet to work?

    Thanks.

    Tom - Antwort

    If you remove just the back cover - which to the uninitiated does look less scary than trying to get between the bezel and the display - you will destroy the tiny plastic rivets that lock the cover onto the bezel. More importantly, you will then find that getting to the parts you need to replace is rendered impossible because they will be hidden under the bezel, which of course will still be in place. So the correct way to take this tablet apart is the more challenging way i.e. separate the front display from the bezel and rear. But with care and the right tools this is still not too difficult. And if you are in any doubt about this, it is worth pointing out that in all of the photos below from Step 4 onwards, the work shown is taking place with the bezel removed. There is nothing written in this guide to indicate that this had to be done.

    PhilipHN - Antwort

  4. Laptop-Akkus

    Wenig Aufwand, große Wirkung.

    Jetzt kaufen

    Laptop-Akkus

    Wenig Aufwand, große Wirkung.

    Jetzt kaufen
  5. Starting with the right speaker, remove the 10 mm Phillips #000 screws. Use the spudger to begin pulling out the speaker. Wedge the spudger beneath the amplifier to remove it from the adhesive holding it down.
    • Starting with the right speaker, remove the 10 mm Phillips #000 screws.

    • Use the spudger to begin pulling out the speaker.

    • Wedge the spudger beneath the amplifier to remove it from the adhesive holding it down.

  6. Remove the two 10mm Phillips #000 screws that hold the left speaker. Remove the two 10mm Phillips #000 screws that hold the left speaker. Remove the two 10mm Phillips #000 screws that hold the left speaker.
    • Remove the two 10mm Phillips #000 screws that hold the left speaker.

  7. Take a pair of tweezers and disconnect the left battery.
    • Take a pair of tweezers and disconnect the left battery.

  8. Use the same pair of tweezers to begin removing the left speaker. There are three slots surrounding the speaker that can be used to remove it. There are three slots surrounding the speaker that can be used to remove it.
    • Use the same pair of tweezers to begin removing the left speaker.

    • There are three slots surrounding the speaker that can be used to remove it.

  9. Pull the speaker out and lay it to the side until the rest of the connections are disconnected. Pull the speaker out and lay it to the side until the rest of the connections are disconnected.
    • Pull the speaker out and lay it to the side until the rest of the connections are disconnected.

  10. There are four slots that are located along the border that can be used to remove the strip that is glued to the side. Wedge the tweezers in each slot to carefully remove the strip. Wedge the tweezers in each slot to carefully remove the strip.
    • There are four slots that are located along the border that can be used to remove the strip that is glued to the side.

    • Wedge the tweezers in each slot to carefully remove the strip.

Abschluss

To reassemble your device, follow these instructions in reverse order.

3 weitere Nutzer haben diese Anleitung absolviert.

Jordan Soto

Mitglied seit: 26.08.2015

2.612 Reputation

6 Anleitungen geschrieben

Team

USF Tampa, Team 3-2, Eyestone Fall 2015 Mitglied von USF Tampa, Team 3-2, Eyestone Fall 2015

USFT-EYESTONE-F15S3G2

3 Mitglieder

18 Anleitungen geschrieben

Thanks, but I have one big question. I removed the back cover, but I still have no idea how to remove the white plastic frame that covers the outer edge of the speakers. In your guide, it just seems to magically disappear.

fongs89 - Antwort

Absolutely right. See my comment above. Carefully prising with the right tools between the display and the frame - the bezel - and working around the outside of the display will eventually cause the bezel to come away from the display with the back cover attached. You can then access the parts you need to get to.

PhilipHN - Antwort

Kommentar hinzufügen

Statistik anzeigen:

Letzte 24 Stunden: 4

Letzte 7 Tage: 11

Letzte 30 Tage: 47

Insgesamt: 3,189