Einleitung
Hier wird der Austausch der Batterie, ohne Löten, gezeigt. Es wird dadurch in Zukunft leichter, die Batterie zu wechseln. Achte darauf, welchen Batterietyp deine Cartridge benötigt.
Beachte: Wenn du die Batterie nicht anlötest, riskierst du, dass sie den Kontakt verliert. Dies könnte zu Datenverlust beim Abspeichern führen.
Was du brauchst
-
-
Trage ein Erdungsarmband. Halte die ROM Platine gut fest und benutze ein geeignetes Werkzeug (Skalpell, Schnitzmesser), um die obere Kontaktfahne der alten Batterie mit langsamen Rüttelbewegungen abzuhebeln.
-
Dazu brauchst du schon etwas Kraft. Achte darauf, dass du dabei die Kontaktfahne nicht von der Platine loshebelst. Beginne an der Spitze der Fahne zu hebeln.
Hello! I recently decided to restart a fresh playthrough of my Pokémon emerald, but I came across the dry battery problem and am planning on fixing it using this method in the next few weeks. I was wondering what exactly you mean by being “grounded”. I know what the term means, but I don’t know if you mean “grounded” like with welding. Thank you in advance!
Grounded as in electrically grounded so as not to short out the chipset. There are bracelets and mats as examples that can be used. The bracelets are usually pretty cheap but will do the job in my opinion.
-
-
-
-
Die kleinen Erhebungen an den Kontaktenfahnen, mit denen sie an der Batterie befestigt waren, kannst du, falls nötig, mit einem Schleifpapier glätten.
-
-
-
Stecke die neue CR1616 Batterie zwischen die beiden Kontaktfahnen. Die positive Seite ist mit einem Aufdruck versehen und muss nach unten zeigen.
What amperage should i use for the battery? it doesn't specify and I've found CR2025 batteries in different amperages.
You don't need to worry about amperage when buying a battery. Whatever is pulling power from the battery will automatically draw the correct amperage.
If you meant amp-hours: you don't need to worry too much about this either. Amp-hours is how much energy is in the battery. Most batteries of the same type have about the same amount of power packed into them; unless you buy fake ones from china off of ebay.
hooper -
-
-
-
Klemme die Fahnen mit einem Isolierband gut fest. Führe das Band unter der unteren und über der oberen Fahne entlang.
-
Bevor du das Band befestigt solltest du die Kante der Batterie dort mit etwas Isolierband bekleben, wo die obere Fahne die Kante berühren könnte. Du vermeidet damit einen Kurzschluss und Aufregungen.
-
-
-
Setze die ROM Platine in die Unterseite des Cartridgegehäuses ein. Setze das Gehäuseoberteil auf und schraube die Y1 Schraube wieder fest.
The battery in the picture is the original one! The CR2032 won't fit and the plastic shell won't close!
Yes I know it is the original, but it is not the point though, it is the principal of just putting it back together the way you started. The CR2032 is a big battery and i tried it in my my own copies of Ruby and Sapphire and it bulges the case but the case will go back together and fit *snugly* into a GBA slot and it does work. As stated in the guide try to use a CR2025 or a CR2016, they should fit better with the case.
Does replacing the battery delete save data?
I have a pokemon emerals cart with over 200 hours in it. I want to use the time events without deleting my data. How would I do this?
No, replacing the battery doesn't erase saved data. It just starts up timed events again and gets rid of the "dry batter" message.
and it allows the player to transfer to diamond and pearl again
-
-
-
Prüfe, ob die Reparatur erfolgreich war, indem du das Spiel in ein kompatibles Gerät einsteckst. (Gameboy Advance SP, Gameboy Micro, DS oder DS lite)
-
Wenn die Fehlermeldung immer noch erscheint, dann prüfe nochmals, ob die Metallfahnen wirklich guten Kontakt mit der Batterie herstellen.
-
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Um dein Gerät wieder zusammenzusetzen, folge den Schritten in umgekehrter Reihenfolge.
Rückgängig: Ich habe diese Anleitung nicht absolviert.
17 weitere Nutzer:innen haben diese Anleitung absolviert.
Besonderer Dank geht an diese Übersetzer:innen:
100%
Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›
9 Kommentare
What i would like to know is why do people mention all these various battery numbers. The board says cr1616 right on it. And that battery is available just as easy as the others and is what belongs in it.
Don't use anything but CR1616 Batteries, it bulges the cartridges case, cracking it over some time and adding wear to the games label.
I recently bought a sapphire that someone broke off the arms and tabs completely off the board. Can I still solder on a new battery to the board even though there is no old solder left on the positive side of the board?
Soldering a new battery and new tabs is very simple, you just need to buy some solder and a soldering iron if you dont already have it and just simply reattatch it with them, the way its supposed to be done
You should be able to as long as nothing on the board itself was damaged. Clean up any excess solder and possibly broken pieces. Get the new battery contacts to solder on and new battery. Install and it should be fine. Good luck
kbuncher -
Will this guide work for a copy of Mario vs Donkey kong?
Anyone reading this method do not do it as it is a dangerous method using a blade near a battery and it is also the incorrect way in replacing these batteries.
I also like how in step 5 you replace it with the wrong size battery with tape and then it shrinks back down to the old size battery and the tape is mysteriously gone :O [can i get some of this magic vanish tape plz dm me ;) ]
i dont have a triwing screwdriver! what else can i use?
CJ Natara - Antwort
Sorry for the delay, but in order to make sure you don't strip the screw, i would suggest buying the Tri-wing screwdriver. Besides you never know when you may need a Tri-wing in the future.
Benjamin Cunliffe -
I bought a Y1 for this project and it is too big! It looks like a Y0 would do the trick.
Jon Ohman - Antwort