Zum Hauptinhalt wechseln

Diese Übersetzung enthält möglicherweise noch nicht die neuesten Änderungen der Original-Anleitung. Hilf mit, die Übersetzung zu aktualisieren oder sieh dir die Original-Anleitung an.

Gehäuse-Frontplatte des optischen Laufwerks

Grundständige Anleitung
Dies ist eine grundständige Anleitung, die nur als Teil einer anderen Anleitung verwendet werden sollte.

Was du brauchst

  1. Gehäuse-Frontplatte des optischen Laufwerks, Gehäuse-Frontplatte des optischen Laufwerks: Schritt 1, Bild 1 von 1
    • Entferne die drei 3,0 mm Kreuzschlitz #0 Schrauben aus dem Gehäuse des optischen Laufwerks.

    Hello, is the sata & power cabla from the mac can directly feet inside the SSD?

    Roman Quenin - Antwort

    plug in the back of the ssd

    Roman Quenin -

    I'm trying to find out as well. I read elsewhere you need something like this without the bracket: http://www.amazon.com/gp/product/B0056OB...

    However I have NOT confirmed this.

    Allen Borza -

    If I understand you correctly; the enclosure allows you to use the existing iMac optical cable. Also the enclosure allows for a safe fitting of the optical drive. In my newer machine I had to double side tape the SSD to the back of the iMac and buy a special cable. Note: this was not an optical drive replacement scenario or I would have done exactly as this tutorial suggests.

    EkDor - Antwort

    I bought another caddy, not the one from the description. i had to extract the plastic adaptor from the optical drive and put in on the new caddy 12,7mm

    Cristian Pizarro - Antwort

    The SDD caddy I purchased was 22 pin SATA both inside and outside so that the optical drive cable (13 pin) would not fit. Does anyone know where I can find a SDD caddy with 13 pin SATA outside for the optical cable and 22 pin SATA inside for the SDD?

    benja.mcg - Antwort

  2. Gehäuse-Frontplatte des optischen Laufwerks: Schritt 2, Bild 1 von 3 Gehäuse-Frontplatte des optischen Laufwerks: Schritt 2, Bild 2 von 3 Gehäuse-Frontplatte des optischen Laufwerks: Schritt 2, Bild 3 von 3
    • Öffne das Gehäuse, indem du von der linken Kante ausgehend vorsichtig ziehst.

    • Ziehe weiter an den beiden Gehäusehälften, bis sie sich trennen.

    This is the 12.7mm caddy.. but, the caddy 9.5 mm fit fine as well? or it doesn't fit on imac mid 2010

    Cristian Pizarro - Antwort

    My caddy (ordered 5/2019) had two additional screws that needed to be removed from the sides for it to open.

    mr.kaufman7 - Antwort

  3. Gehäuse-Frontplatte des optischen Laufwerks: Schritt 3, Bild 1 von 1
    • Entferne die beiden 3,0 mm Kreuzschlitz #0 Schrauben, mit welchen die Frontblende am Gehäuse des optischen Laufwerks befestigt ist.

  4. Gehäuse-Frontplatte des optischen Laufwerks: Schritt 4, Bild 1 von 3 Gehäuse-Frontplatte des optischen Laufwerks: Schritt 4, Bild 2 von 3 Gehäuse-Frontplatte des optischen Laufwerks: Schritt 4, Bild 3 von 3
    • Hebe die schwarze Kunststoff-Frontplatte aus dem Gehäuse der Optical Bay.

    • Du benötigst weder die Frontblende noch die beiden Kreuzschlitz Schrauben, mit denen sie an ihrem Platz gehalten wurde. Bewahre die Teile für den Fall auf, dass du jemals wieder die Frontblende in das Gehäuse einsetzen möchtest.

    • Baue das Gehäuse des optischen Laufwerks ohne die Frontplatte unter Verwendung der drei originalen 3,0 mm Kreuzschlitz Schrauben wieder zusammen.

    Just curious, why is it necessary to remove this black plastic faceplate from the enclosure? It doesn't appear to serve any function in or out of the enclosure.

    Nic Johnson - Antwort

    Maybe because it would interfere with the bracket you have to put back on in step 21?

    Jeff Dickson -

    So I'm confused about the Optical Drive Bracket, the one that originally held the DVD-CD drive. I had an awful time remounting the kit into that bracket as the screws didn't line up correctly. I finally got everything to fit, less one of the four holding screws. Did anyone else experience this problem? I would have expected a much better alignment for this assembly considering the quality of the iFixIt site.

    For the record, the upgrade went fine with a SanDisk Extreme II 480GB SSD, but that one step was next to impossible, and not covered in any detail by the instructions.

    Ron Lockhart - Antwort

    Yep, I had exactly the same problem. The alignment was way off.

    olafgoy -

    My kit also did not line up correctly. I had to put all four screws in at an angle cross-threaded to mount the unit.

    Kevo -

    Same here. managed to get two screws in at a decent angle on one side and couldn't get the others in. Felt solid enough once I'd screwed the original ODD casing back onto the iMac.

    Monkeyrebirth -

    I had the same alignment problem, too. I ended up removing the rubber grommets from the plastic enclosure, widening the holes with a small file, then replacing the grommets. All four screws went in, but not in perfect alignment. Should be ok, though.

    nickmalmquist -

    Another possibility is the part has been designed to be used with different types of iMac and some utilise this component. In this case it apparently doesn't.

    EkDor - Antwort

    I bought a different enclosure than the one recommended ($18 instead of $39) and it came with new screws because the old screws were too big to fit in the holes for the new enclosure.

    Keith Mewis - Antwort

    Hi. Which enclosure did you buy? link please.

    Alex -

    Where did you get the alternative enclosure from?

    Walter Poole -

    I completed this guide last night on my iMac and it all worked great until I got to step 26 and none of the holes on the 12.7 mm PATA Optical Bay SATA Hard Drive Enclosure lined up with the black plastic faceplate. Just like what is being commented on by previous fixers, I could only get 2 screws on one side of the enclosure in, but they were crooked and unable to screw in all the way. It was crude, but it worked.

    The rest of this guide works flawlessly. This is a great site!

    Marc - Antwort

Abschluss

Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.

Besonderer Dank geht an diese Übersetzer:innen:

en de

75%

Diese Übersetzer:innen helfen uns, die Welt zu reparieren! Wie kann ich mithelfen?
Hier starten ›

Brittany McCrigler

Mitglied seit: 03/05/12

88.898 Reputation

131 Anleitungen geschrieben

Team

iFixit Mitglied von iFixit

Staff

136 Mitglieder

16.573 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 0

Letzte 7 Tage: 0

Letzte 30 Tage: 0

Insgesamt: 724