Zum Hauptinhalt wechseln

Giant Reign 2 Tube Replacement

Was du brauchst

  1. Giant Reign 2 Tube Replacement, Hex Screws: Schritt 1, Bild 1 von 1
    • Using the 4mm Allen wrench, partially unscrew the 4 (22mm) hex screws on the front of the axle casing to allow the axle to slide freely.

  2. Giant Reign 2 Tube Replacement, Axle Screw: Schritt 2, Bild 1 von 2 Giant Reign 2 Tube Replacement, Axle Screw: Schritt 2, Bild 2 von 2
    • Using the 8mm Allen wrench, loosen the axle screw until 1/2 of the axle screw is visible.

    • Push the axle screw to reveal the axle rod on the other side.

  3. Giant Reign 2 Tube Replacement: Schritt 3, Bild 1 von 1
    • Using the Allen wrench, finish unscrewing the axle screw and pull it out.

    • Hold the wheel when pulling out the axle rod so that the bike does not fall.

  4. Giant Reign 2 Tube Replacement, Front Wheel: Schritt 4, Bild 1 von 1
    • Pull the wheel from the fork.

  5. Giant Reign 2 Tube Replacement, Tube: Schritt 5, Bild 1 von 1
    • Look at your tire and determine the correct tube size by locating the number (formated ## x #.##) on the wall of the tire.

    • Bike tubes come with one of two standard valve types: presta and schrader. These guides show the installation of a tube with a presta valve.

  6. Giant Reign 2 Tube Replacement: Schritt 6, Bild 1 von 3 Giant Reign 2 Tube Replacement: Schritt 6, Bild 2 von 3 Giant Reign 2 Tube Replacement: Schritt 6, Bild 3 von 3
    • Unscrew the cap covering the valve.

    • Remove the spacer that holds the valve in place against the rim of the wheel.

    • Open the valve by turning the nut and pressing the valve in to release air pressure from the tube.

  7. Giant Reign 2 Tube Replacement: Schritt 7, Bild 1 von 3 Giant Reign 2 Tube Replacement: Schritt 7, Bild 2 von 3 Giant Reign 2 Tube Replacement: Schritt 7, Bild 3 von 3
    • Slide the tire lever between the tire and the rim.

    • Push down on the tire lever until the edge of the tire is higher than the edge of the rim.

    • Insert a second tire lever adjacent to the first.

    • Slowly work one tire lever around the rim until the whole tire is loose.

  8. Giant Reign 2 Tube Replacement: Schritt 8, Bild 1 von 2 Giant Reign 2 Tube Replacement: Schritt 8, Bild 2 von 2
    • Press the valve through the rim of the wheel.

    • Remove the tube from the tire.

  9. Giant Reign 2 Tube Replacement: Schritt 9, Bild 1 von 1
    • Partially inflate the tube.

  10. Giant Reign 2 Tube Replacement: Schritt 10, Bild 1 von 2 Giant Reign 2 Tube Replacement: Schritt 10, Bild 2 von 2
    • Push the valve through the rim.

    • Push the tube into the tire all the way around the rim of the wheel.

  11. Giant Reign 2 Tube Replacement: Schritt 11, Bild 1 von 1
    • Push the bead of the tire back into place around the rim.

    • Make sure not to pinch the tube between the bead of the tire and the rim. Failure to do so may cause a pinch flat.

  12. Giant Reign 2 Tube Replacement: Schritt 12, Bild 1 von 1
    • Inflate the tube to the desired air pressure.

    • A suggested range of air pressure is located on the wall of the tire (formatted ##-##psi).

  13. Giant Reign 2 Tube Replacement: Schritt 13, Bild 1 von 2 Giant Reign 2 Tube Replacement: Schritt 13, Bild 2 von 2
    • Close the valve and replace the cap.

Ziellinie

Ein:e weitere:r Nutzer:in hat diese Anleitung absolviert.

Team

Cal Poly, Team 9-14, Amido Fall 2012 Mitglied von Cal Poly, Team 9-14, Amido Fall 2012

CPSU-AMIDO-F12S9G14

4 Mitglieder

10 Anleitungen geschrieben

0 Kommentare

Kommentar hinzufügen

Seitenaufrufe:

Letzte 24 Stunden: 1

Letzte 7 Tage: 4

Letzte 30 Tage: 17

Insgesamt: 2,837